6066 (1960-1966) GMC Truck Club

6066 (1960-1966) GMC Truck Club (https://6066gmcclub.com/index.php)
-   GMC V6 and V12 Engines (https://6066gmcclub.com/forumdisplay.php?f=9)
-   -   Question about switching to a Holley 500 (https://6066gmcclub.com/showthread.php?t=49953)

wcstory April 16th, 2017 02:26 AM

Question about switching to a Holley 500
 
I purchased a 4412s Holley 500 to make my 305e breathe a little better. I also have a 70's style gas pedal assembly and new throttle cable to replace the solid linkage.

What throttle bracket do I need to install the 500cfm with a newer style cable?

I will be installing a 700r4 next step once the Lokar shifter and lockup harness come in.

Quigley April 16th, 2017 02:19 PM

Re: Question about switching to a Holley 500
 
On my 66 with a Powerflow the stock throttle linkage worked perfect on the Holley. Choke cable was too short, because the hookup was on the other side of carb. :ok: Dave

wcstory April 16th, 2017 03:29 PM

Re: Question about switching to a Holley 500
 
I decided to read the documentation that came with the 4412 Holley :banghead:

Holley 20-95 Throttle Cable Bracket

Holley 20-89 Return Springs


From the 60-66 GMC site

Mr. Gasket Adapter #720-1937.

XRP 700106 Size 6 to 7/8-20 Holley Carburetor Adapter

XRP 239006 Size 6 90 Degree Push-On Hose End

I think I may have the manifold machined flat and weld a Holley base plate onto it.

bigblockv6 April 16th, 2017 03:57 PM

Re: Question about switching to a Holley 500
 
I think I may have the manifold machined flat and weld a Holley base plate onto it.[/QUOTE]

It wouldn't be necessary to go through all that, what I have done is opened up base on the manifold with a die grinder to match the throttle plate bores of the Holley as well as open the bores of the adapter. You don't want the carb sitting too low on the manifold. Many GMC V6 engine used spacers between the carb & manifold, this helped with velocity. Some 351C and many 379 engines in Medium duty trucks actually came with a 8 to 10 inch tunnel ram:upyes:

wcstory April 16th, 2017 04:32 PM

Re: Question about switching to a Holley 500
 
1 Attachment(s)
Do the 305 manifolds normally have the carb sitting at an angle? The one I picked up to modify definitely does.

Culver Adams April 16th, 2017 05:14 PM

Re: Question about switching to a Holley 500
 
Hello Wcstory,

Regarding angle: the engine is designed to sit at a nose-high angle. The angle you see at the carby is to keep the carby level.

Regards and Hope that helps,

Culver

bigblockv6 April 16th, 2017 05:45 PM

Re: Question about switching to a Holley 500
 
Quote:

Originally Posted by wcstory (Post 66806)
Do the 305 manifolds normally have the carb sitting at an angle? The one I picked up to modify definitely does.

The angle on the manifold is typical of most all carbureted GM V6 & V8 engines of the 60's & 70's:upyes:


All times are GMT +1. The time now is 08:10 PM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.