6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > I-6 Engines


I-6 Engines For GMCs that came with the Inline 6 Engines

Reply
 
Thread Tools
  #1  
Old July 6th, 2017, 01:54 AM
Dano64's Avatar
Dano64 Dano64 is offline
Junior Member
 
Join Date: Jun 2017
Location: corvallis, oregon
Truck: 64 PU
Age: 51
Posts: 26
Rep Power: 49
Dano64 is on a distinguished road
Default Going to HEI distributor and screwing up (a lot?)

Hi guys.

Got my 64 maybe a month ago and it was running roughly. Not so so bad but high idle needed to not stall. Determined that the timing and/or ignition might be screwy so set out to improve it as this is really the only major issue between the truck being driveway decoration and usable.

Setting aside the idea that I may have been wrong about the entire source of problems - like whether the distributor/timing was an issue at all (sigh) I am committed to the new distributor now. Likely mistake #1. Not really worried if this wasn't the original problem as I'm sure this ultimately will make it a better runner.

OK; here are the main points.

Thought I had an old mechanical distributor with no vacuum advance because that's all I saw from the top and I didn't look closely (mistake #2 if we're keeping count). Turns out it was a Pertronix Ignitor II electronic unit, likely installed in 2011 when motor was rebuilt. No vacuum. Maybe fine. Maybe toast.

Read some posts here from TJ and did some online research; had a hard time finding top dead center and tried replacing the distributor by simply matching the rotor position. Goof #3?

I felt like that was a success then realized I had wired my distributor for CCW instead of CW. #4. (sigh; rewired) and it seemed like maybe the two distributors were not "clocked" the same way so I lost faith in the correctness of the rotor position also.

(stopping the mistake count, too embarrassing)

Realized that where I had the number one wire was a few positions different than where EVERY OTHER distributor seemed to be compared to photos online. Combining this with the loss of faith in the correctness of the rotor position and I moved the wires again, carefully checking the correct firing sequence (and doing it CW!). No Fire.

Unable to feel confident about a TDC check, and compulsively 'doing something' yesterday I trusted the marks on the harmonic and set the timing (manually, not running) to about 4° BTDC by lining up the rotor to #1 plug wire. No fire. Also tried various timing positions after that, spitting gas vapors out of carb and feeling like a genius while my son holds the hose and has safety glasses on nearby. (Not *that* near.)

Sigh.

So it ran better when I got it than it does now. Suggestions on what I imagine is like doing a distributor job on an engine that is not 'known good'? Sigh.
Reply With Quote
  #2  
Old July 6th, 2017, 03:20 PM
TJ's GMC's Avatar
TJ's GMC TJ's GMC is offline
Senior Member
 
Join Date: Mar 2015
Location: Cave Junction, Oregon
Truck: 1964 GMC 1500 LWB Wideside 305E V6.
Posts: 1,341
Rep Power: 399
TJ's GMC is on a distinguished road
Default Re: Going to HEI distributor and screwing up (a lot?)

As long as the firing order is correct you can place number 1 on the dizzy wherever you want. Can you show some pictures of your setup?
If you'd like I could make a video walking you through setting the timing and checking for spark.
__________________
"Excuse the rust I use my truck"
1964 GMC 1500 305E/sm420 4 barrel intake mod and dual exhaust.
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

1964 Chevy C20 292/SM420
1966 Chevy C10 292 hotrod 6/TKO600


My youtube channel aka Military Chevy:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #3  
Old July 16th, 2017, 11:38 PM
Dano64's Avatar
Dano64 Dano64 is offline
Junior Member
 
Join Date: Jun 2017
Location: corvallis, oregon
Truck: 64 PU
Age: 51
Posts: 26
Rep Power: 49
Dano64 is on a distinguished road
Default Re: Going to HEI distributor and screwing up (a lot?)

Hi. I made a video of what I'm looking to do. Would you tell me if this makes sense?? Thank you.

Updated the link, I posted one that wasn't shared at first.

https://drive.google.com/file/d/0B27...ew?usp=sharing

Last edited by Dano64; July 17th, 2017 at 06:12 AM.
Reply With Quote
  #4  
Old July 17th, 2017, 02:16 AM
Dano64's Avatar
Dano64 Dano64 is offline
Junior Member
 
Join Date: Jun 2017
Location: corvallis, oregon
Truck: 64 PU
Age: 51
Posts: 26
Rep Power: 49
Dano64 is on a distinguished road
Default Re: Going to HEI distributor and screwing up (a lot?)

Holy crap it worked. The lifter checking method got me to a reliable TDC; from there I found my rotor was inexcusable off and it would have never worked. First try it fired up after that.

Following that... lots of futzing with timing then realized that timing with the vacuum on was all wrong...

Got to a non-vacuum timing of about 4 degrees and smooth (mostly) idle of about 1500 w/o choke.

I think I need to move it to 6-8 but I'm taking a glory-I-got-it-running drive first.
Reply With Quote
  #5  
Old July 18th, 2017, 03:33 AM
TJ's GMC's Avatar
TJ's GMC TJ's GMC is offline
Senior Member
 
Join Date: Mar 2015
Location: Cave Junction, Oregon
Truck: 1964 GMC 1500 LWB Wideside 305E V6.
Posts: 1,341
Rep Power: 399
TJ's GMC is on a distinguished road
Default Re: Going to HEI distributor and screwing up (a lot?)

Don't be afraid to advance the timing to 10 degrees, I've experienced and so have many others that there can be lost power with so little initial. Try it at 8 and if it has good power then leave it, but if you notice it's sluggish or pulls hills poorly try advancing a little more. Glad it's running! Drive the wheels off it!
__________________
"Excuse the rust I use my truck"
1964 GMC 1500 305E/sm420 4 barrel intake mod and dual exhaust.
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

1964 Chevy C20 292/SM420
1966 Chevy C10 292 hotrod 6/TKO600


My youtube channel aka Military Chevy:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #6  
Old July 22nd, 2017, 09:08 PM
Dano64's Avatar
Dano64 Dano64 is offline
Junior Member
 
Join Date: Jun 2017
Location: corvallis, oregon
Truck: 64 PU
Age: 51
Posts: 26
Rep Power: 49
Dano64 is on a distinguished road
Default Re: Going to HEI distributor and screwing up (a lot?)

Ok, thanks! This is just what I'll do. Then... I think... I will try adjusting carb mixture with vacuum gauge. That's just warming up motor and tinkering for max vac, yeah?
Reply With Quote
  #7  
Old August 4th, 2017, 06:39 AM
TJ's GMC's Avatar
TJ's GMC TJ's GMC is offline
Senior Member
 
Join Date: Mar 2015
Location: Cave Junction, Oregon
Truck: 1964 GMC 1500 LWB Wideside 305E V6.
Posts: 1,341
Rep Power: 399
TJ's GMC is on a distinguished road
Default Re: Going to HEI distributor and screwing up (a lot?)

Max I was able to pull was 16-18 with my 305. Initial at 8 degrees. 4-6 is the spec.
__________________
"Excuse the rust I use my truck"
1964 GMC 1500 305E/sm420 4 barrel intake mod and dual exhaust.
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

1964 Chevy C20 292/SM420
1966 Chevy C10 292 hotrod 6/TKO600


My youtube channel aka Military Chevy:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
Reply

Bookmarks

Tags
250, distributor, timing

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
New HEI Distributor Buffalo GMC V6 and V12 Engines 8 January 22nd, 2014 08:18 AM
HEI Distributor Archiver Previous Forum Posts 0 September 8th, 2011 01:51 AM
HEI Distributor Archiver Previous Forum Posts 2 November 9th, 2010 08:44 AM
hei distributor Archiver Previous Forum Posts 0 November 28th, 2009 05:24 AM
Hei distributor Archiver Previous Forum Posts 0 May 17th, 2006 01:55 AM


All times are GMT +1. The time now is 06:11 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 681711554703|1710436270|0