Pay Dues or become a Site Supporter
|
Pay Dues or become a Site Supporter
|
|
#1
May 24th, 2013, 05:39 PM
|
||||
|
||||
Looking for Piston
OK Guys I have been looking for a piston that will fit inside the crank end of a 351 connecting rod, its 2.9", any one know what engines use a piston that is 2.9" Diameter?
__________________
Links to Other Places: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. on FacePage. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. . the To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. on FacePage. Owner of: 1965 GMC 3500 Custom Rescue Squad {Black Built Bodies} 1968 Ford Galaxie 500 Convertible 2006 Yamaha Rhino 450 2008 GMC HHR Panel. 
|
|
#2
May 24th, 2013, 10:19 PM
|
||||
|
||||
|
Re: Looking for Piston
I'm not sure of your question as to why you want to put a piston thru the big hole in a rod, but....
I would try some outboard motor sizes, and briggs & stratton catalogs.
__________________
Jon S Las Vegas Nv 1966 GMC Suburban 305 V6
|
|
#3
May 25th, 2013, 12:50 PM
|
||||
|
||||
|
Re: Looking for Piston
It will be for display at shows, been doing some research and mite have found a few to check on.
__________________
Links to Other Places: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. on FacePage. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. . the To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. on FacePage. Owner of: 1965 GMC 3500 Custom Rescue Squad {Black Built Bodies} 1968 Ford Galaxie 500 Convertible 2006 Yamaha Rhino 450 2008 GMC HHR Panel.
|
|
#4
June 2nd, 2013, 05:41 PM
|
||||
|
||||
|
Re: Looking for Piston
Summit racing has 2 pistons 2.904"
http://www.summitracing.com/parts/ue...75mm/overview/ They also have 2 that are 2.894" which is just under 2.9". http://www.summitracing.com/parts/ue...-5mm/overview/ One is out of a 1987 Toyota L4 4-cylinder 1.5 liter Not hard to find stuff, ya just gotta look.. Good luck
__________________
Jon S Las Vegas Nv 1966 GMC Suburban 305 V6
|
|
#5
June 2nd, 2013, 05:44 PM
|
||||
|
||||
|
Re: Looking for Piston
PS: Just go to Summit Racing website, put in pistons, then bore size. It will give you a list of available pistons. When you click on check application, it will tell you what engine it fits.
__________________
Jon S Las Vegas Nv 1966 GMC Suburban 305 V6
|
|
#6
June 3rd, 2013, 04:31 AM
|
||||
|
||||
|
Re: Looking for Piston
"Not hard to find stuff, ya just gotta look.."
Yes I know that I have been looking nd found a few, just need to find one I can get cheap, been watching ebay for some.
__________________
Links to Other Places: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. on FacePage. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. . the To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. on FacePage. Owner of: 1965 GMC 3500 Custom Rescue Squad {Black Built Bodies} 1968 Ford Galaxie 500 Convertible 2006 Yamaha Rhino 450 2008 GMC HHR Panel.
|
|
#7
June 16th, 2013, 05:40 AM
|
||||
|
||||
|
Re: Looking for Piston
I found a piston I could use for this project, I needed to remove one rod bearing half to get it to fit. This is a 351C Piston & Rod with a Yamaha 750 Piston through the rod crank journal hole.
 This will be a display for car & truck shows.
__________________
Links to Other Places: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. on FacePage. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. . the To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. on FacePage. Owner of: 1965 GMC 3500 Custom Rescue Squad {Black Built Bodies} 1968 Ford Galaxie 500 Convertible 2006 Yamaha Rhino 450 2008 GMC HHR Panel.
|
|
#8
July 26th, 2013, 03:32 AM
|
||||
|
||||
|
Re: Looking for Piston
Piston & Rod on the left are from a GMC Big Block V6 {351}, the Piston in the GMC rod is the size of many of the V6 engines in cars & Trucks today, {this one is really a Yamaha 660 Piston, it cost me $1 but its the size that counts here}. tH really small piston & Rod on the right is from a 3 cylinder Suzuki Mini Truck Engine.
__________________
Links to Other Places: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. on FacePage. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. . the To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. on FacePage. Owner of: 1965 GMC 3500 Custom Rescue Squad {Black Built Bodies} 1968 Ford Galaxie 500 Convertible 2006 Yamaha Rhino 450 2008 GMC HHR Panel.
|
 |
| Bookmarks |
| Thread Tools | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Re: [6066 GMC] I Need a Piston, A BIG Piston! | Archiver | Previous Forum Posts | 0 | May 18th, 2009 04:20 AM |
| Re: [6066 GMC] I Need a Piston, A BIG Piston! | Archiver | Previous Forum Posts | 0 | May 17th, 2009 01:19 AM |
| 702/351 Piston? | Archiver | Previous Forum Posts | 0 | September 23rd, 2007 01:21 AM |
| Re: Need 351 Piston bad | Archiver | Previous Forum Posts | 0 | November 24th, 2003 12:13 AM |
| piston help | Archiver | Previous Forum Posts | 0 | May 10th, 2003 03:24 AM |
