My 64 GMC 1500
 

A 1964 GMC 1500 Fleetside was will to my wife from her father. It has a 305E V6 with a 4 speed SM420 transmission. When I went to pick it up it had no brakes, a dead battery, and old gas in the tank. Body is in bad shape, no major rust just several dents.

I started to examine the truck for needed repairs.

I inspected the brakes system (it has 8 lugs drums on all four corner). I checked the Internet for replacement parts. I soon determined that it should be upgraded for safety. For over a year the hand brake was the only brake I had. I searched the Internet for an 8 lug disc brake conversion kit (trying to maintain the original look). The only thing I found was the rear axle conversion kit. I piece together part from an 81 GMC 1500 and 2500 front brake system. I fabricated my own brake lines. Installed a dual cylinder master cylinder with a stainless 7" dual cylinder booster and a proportioning valve. Modified the brake pedal and bled the brakes system. I also found the forward hand brake cable was coming apart and replaced it with a new cable. When I went to connect the vacuum hose to the intake manifold I discover it was installed backward. So I removed, cleaned, painted and reinstalled the intake manifold.

While I was cleaning the rear axle housing, I had drained it. Only a quarter of a cup of oil came out. I removed the cover and found the gears was ate up. I removed the rear axle and removed the 4.10:1 gear set and installed a 3.54:1 gear set with all new bearing. This axle is a full floater. When I removed the hubs and the bearings was filled with grease (instead of rear axle oil), the seal had ate a groove in the spindle. I installed new bearings and seals in the hubs. I repaired the spindle with Devcon titanium putty (has the best chemical and temperature resistance spec).

On the engine (while waiting on brake parts to come in) I replaced all hoses and flushed the coolant system, added new coolant, new points, condenser, and cleaned the plugs. I removed the valve cover and removed both rocker assemblies and cleaned out the sludge from the shafts. Reassembled and adjusted the valve lash (Hot). I then cleaned, painted and reinstalled the valve cover. Now that I got it running the water pump started to leak, I installed a new pump. While I was doing that I removed the fan shroud that was on it. It was butchered up when the air conditioner was installed (will repair it later).

I replaced the engine oil several times during the course of the work and the transmission once (with synchromesh oil). I had also had the seat recovered.

Now I have it in a running condition and now have 70 miles on it, from running around the neighborhood. Today I am removing the driveshaft to clean and paint it. While it out, on the two piece drive shaft, the support bearing is getting replace and I and looking into seeing what gear is in the transmission speedometer drive so I can correct the speedometer reading (may have to use an external device). I did place two picture galley on this site:
Brakes


To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?


General Pictures


To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

Re: My 64 GMC 1500
 

Very nice work James! Should stop nicely now and that gearing change is a nice move.

In the old photo what is that cone shape object attached to the cowl?

Re: My 64 GMC 1500
 

That is a work light that can be removed from the base to light up different area under the hood. Right now I have not repaired it but plan to do so and place it back on, might be in a different location when I put it back on.

Re: My 64 GMC 1500
 

Subbed and nice truck.

Re: My 64 GMC 1500
 

James,

I admire the amount of work that you have put into your 64 GMC 1500. I have a nearly identical 1964 truck that I have had for nearly 40 years (from my father) and am still using. You have had all the problems to fix at once, while I have been working on them over the years. Changing the braking system is a good call. I kept the drum brakes but did install a dual master cylinder after a nearly catastrophic loss of hydraulic brakes when one of the front brake hoses cracked open. It is a good thing that the emergency brake on these trucks really does work - but I too had to replace the front cable. My other major projects were new bed wood (the original lasted nearly 30 years and took another 10 or so with plywood over the bed before I got around to replacing it) and I recently installed a Holley 500 two-barrel carburetor that has given a noticeable increase in power at the expense of gas mileage. I installed a fan clutch thinking it might help mileage and engine noise, but haven't noticed a difference. And I put on newer wheels for tubeless radial tires that greatly improved handling and ride. Other work has been more routine - oil changes, grease, hoses, belts, points, plugs, ignition wires, wiper blades, clutch repair, changing water pumps and fuel pumps, etc. Next, I want to switch from the 4.01 to 3.54 rear end gears (as you have already done) with limited slip to help with fewer rpm at highway speed, better use of second (not counting compound low) gear on hills, and better traction in fields. I also have a Pertronix ignition and coil replacement that I hope to get around to installing, plus some gauges, switches, lights, and a new radio. And I have a 351E to rebuild and put in if the 305E ever gives out. With all this, it is a good truck for work, recreation and reminiscing, but I like the ride and convenience of newer cars for every day driving.

JRMunn

Re: My 64 GMC 1500
 

Old tread but curious if you added brake booster, or just duel master cylinder. I have 64 GMC 3/4 ton and want to upgrade. Not sure if booster way to go.

Charlie

Re: My 64 GMC 1500
 

Because I converted it to 4 wheel disc brake I added a 7" dual brake booster and modified the brake pedal to make it work correctly. Here is a picture of the brake master cylinder/booster:


To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

Re: My 64 GMC 1500
 

Cheeker,

I did not add a brake booster. The truck came with a vacuum boost that my father removed because it was too sensitive (but probably necessary to the first owner who carried a camper and found the 305E underpowered for the weight). I would be cautious about adding a booster if you don't need it for a load. My rear tires lock up on a moderate stop, even with the larger radial tires, and this could be dangerous with added brake power and sensitivity. On the other hand, I can still push hard on the brake pedal.

jrmunn

Re: My 64 GMC 1500
 

I wonder if the vacuum boost/brake booster on your truck was added for the original owner. A common mistake when added is to use the same hole in the pedal. This would make the brake pedal sensitive. The proper way is to drill a hole 1" below (to reduce the pedal ratio) the manual brake hole to reduce the sensitive. With my vacuum boost/brake booster it is not sensitive and I normally have an empty bed.

On another note. If you have 4 wheel drum brakes then that would also make it sensitive. I have 4 wheel disc brake.

Just my thought.

Re: My 64 GMC 1500
 

I carry the Pullman Camper with stuff inside, but certainly not a load. Thanks for your communication as I hoped just adding new dual master cylinder and reworking brakes would be adequate, without a booster.