Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)
 

I always cut mine out from the inside. I just use a utility knife and I follow the metal flange that the seal wraps around. The seal is really thin there. Then just push it out top first. I pull old glass all the time. It takes about 5 minutes to do. I leave the old seal on the glass until I am ready to install. It helps protect the edges of the glass. Barry

Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)
 

Since the windows on these trucks are not glued in (or shouldn't be) this should not be a concern.

Although it is good advice for windows on vehicle with the glued in windshield. Such as my old (long gone to scrap) mid 70's Pontiac...

Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)
 

Do -not- get a torch near it. One "hot spot" while the rest isn't could very easily cause the windshield to shatter...

My '63 4000 had a good windshield, I was removing the overheat rack extensions (cutting them off) and one small piece of slag dropped onto the windshield wiper. Sent cracks out almost immediately.

With the windshield on the 60-63 being more expensive and harder to install/remove I would suggest extreme care if you decide to remove it. Cut slowly, a little at a time. In the past I have heard a horror story or two about someone breaking the window trying to get it in, getting it to seat in the gasket due to the curves. On one of my '61s there is an obvious gap, bottom center of the windshield, in the gasket due probably to shrinkage over the years. During wet weather the rain would bubble through to the inside while driving. After serious contemplation about removing the windshield, I decided to fill the space with clear silicone sealant. Then carefully went around the entire window rubbing sealant into the entire gasket to seal any cracks or other potential problems. I could have just covered it with a bead, but I didn't want it to look like I had added sealant. A little clear sealant and my fingers "massaging" the seal into the cracks and around the edges.

Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)
 

Barry is a lot more brave than me! I have a friend that owns a automotive glass shop in town and he is who I rely on when glass has to be removed, but with some patience and help using his cutting technique gives me a little more confidence now too.

I did a couple of similar repairs on my rock hard windshield gasket on my '55 GMC using standard black Permatex silicone. Permatex makes a clear "flowable" windshield silicon that is a great product. I discovered it by accident many years ago when I was looking for a way to make my own silicone coated sponge tires for racing HO scale slot cars. After that I have used it to repair numerous windshield leaks. See the link below.

I sure have to figure out posting links again now that I'm using Firefox!

DAC



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)
 

I'll look at the inside but I think its just as hard inside as it is out. More like hard plastic than any kind of rubber.



that's a good warning. i didnt think about it cracking the glass.




i put some sealant in the ol cart for my next order. If its a small crack or something I can fill it with that for now and move up to a replacement when the time comes. How did you get that hard 55 gasket removed? Hammer and chisel? :lolflag:

Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)
 

Today I didn't do anything to my truck. She's covered in SNOW!!!

But I did get something in the mail from a fellow member! BarryGMC said a couple of weeks ago that he was sending a present. I figured it'd be a string of welding beads because my welding is pretty crappy but he said, nope! Just keep an eye out. you'll like it. :headscratch:


I waited and waited.. I paced the floor. I did a puzzle. I twiddled my thumbs....



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Finally it came today and after checking it (and grinning like a nut) I let the Powder Puff take over.

She carefully opened the box because I told her it was something very special that she shouldn't scratch up. Then she lost it. Daddy, it's a...it's a...It's a thing like "The Redhead" painted! Ooooh, it's so shinnnneeyyyy!!! (rub rub rub!)



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







I told her we should pose with them for a picture. she said, let me get them right. They have to be perfect you know because they're veeryyy speeecial!



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







I laughed and told her she should be fun with it. She said, Ok, I can just wear them like Cecilia does!

And this picture was born.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







This was such a great surprise. We passed them back and forth several times just looking at them shine. For anyone that doesn't know these are the Custom style emblems. The standard ones, like I have on Cecilia now, are painted white. They shined up real nice, but nothing like this. Here's a pic of them in my fire glow. The reflection was really neat but didn't transfer to a pic very well.

All of you guys are all invited to come over tonight and stare at them twinkling in the firelight with me. Bring a casserole.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Thank you BarryGMC, you surprised two very happy grease-monkeys on a dreary cold day! We can't wait to get Cecilia's new "ear rings" on her. Stay safe up there!:yourock:

Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)
 

LOL---I'm afraid the rock hard gasket is still in the truck! It had 2 gaps like David described that I filled with the black Permatex. So far I haven't needed to use the flowable stuff on it. My door gaskets are where the weather gets in the '55, along with a couple rust holes---. This gasket will stay in until I get more serious about bodywork on it.

Now how cool is that present from Barry? Not only great looking parts but Y'all are having fun with them too! They will be great on your GMC!

May I ask where "Edmond" is?

DAC

Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)
 

She sure is beautiful, Pepsi.
I have a feeling she won't let you get too sad. That's sure a happy face she's got goin' on there.
Me bein a Dad to three gals, youngest 26 yrs.....I sure have a natural understanding for how it goes for you.
For the most part....it's absolutely unbelievable.

But sometimes,....it's absolutely unbelievable how quick you can get your butt kicked by a few little girls.

BTW.....That's a "whole lotta love", Barry.

Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)
 

Great stuff Pepsi . That old girl needs some sparkle. And I really enjoy your enthusiasm . Keep it up. Barry.

Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)
 

Not a real update, but I need to pick up some wood so I slapped her back together a little this warm-ish weekend. I'll need to put the bed temporarily on this next weekend and instead of killing myself I ordered up one of these



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







It comes in 2 boxes and only one arrived yet. So far I have a crossmember and a buncha wheels and bolts but I'm pretty excited about gettin a new toy :D

I've been wanting one forever for picking up the bed and if necessary removing the engine for painting and fiddling. :bananadance: