Quote:
|
I don't have a closed knuckle 44 apart. Just measure the ID and Od of the bushing. I bet I could buy 10 on Tuesday.. Is the inner 1/8 to small on the jeep part. If so I will measure up some jeep stuff. And give you the bushing specs you need. Same if it's the Od. Barry
|
Barry, the bushing I got was from a Dana 25 for a Jeep. It was too small OD and ID.
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
Quote:
|
The bushing for a Willys Jeep will be too small.
Those are model 25/27 and the spindle bushings are too small.
Look for GM part No. 2402596.
You may have to look out for some NOS items. Ebay is a good place to start.
Jonathon
|
Yup
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
It was worth a shot. Sure looked identical in the pics
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
So where have I been the last couple of weeks, you might ask?
H-O-N-E-Y D-O's!
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
The Blonde is normally very understanding about my lil' project but a couple of weeks ago she put her foot down and had me build a koi pond (read Goldfish pond) complete with a fountain and rocks. Talk about a back breaker! And I had more fence repair to do. This whole time Cecilia's been sittin out in the front yard with one leg in the air, like a wounded puppy patiently waiting for me to get my act together and come back to her.
I still haven't gotten there yet. I did get this stuff in for the axles.
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
If you forgot, it's this new grease that has a super low washout factor so it wont degrade or wash away when I drive through water, even submerged like when I drive the boat I don't own off the boat ramp with her. I'm excited about using it.
I did get ahold of a micro thingy and measured my bushing. Here's the specs.
1 1/2 inch Outside Diameter (OD)
1 3/8 inch Inside Diameter (ID)
1 7/8 inch Outside Diameter if you include the lip (OD W/ Lip?)
1 inch tall
Pics:
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?
I really need to get free this week and get her handled and mobile again. I've got a hankering for some cruisin!
Next steps:
Clean parts with Diesel
Order grease seal
Order knuckle seal
Order bearings if I need them. They're Timkins so apparently they're adjustable as they wear down.
Should I slather the entire spindle/axle bit (elephant thingy) with grease when I put it back in or is a nice coating good enough?