Pay Dues or become a Site Supporter
|
Pay Dues or become a Site Supporter
|
|
#1
April 28th, 2015, 04:11 AM
|
|||
|
|||
292 engine pull
Got the 292 running well, but I want to pull it to fix an oil leak and upgrade the cam/cylinder head. Any advice on how to pull the engine while leaving the bellhousing and tranny in place? I drove myself crazy messing with the tranny last summer! Much appreciated for any ideas.
|
|
#2
April 29th, 2015, 04:29 AM
|
||||
|
||||
|
Re: 292 engine pull
Quote:
|
|
#3
April 29th, 2015, 02:18 PM
|
|||
|
|||
|
Re: 292 engine pull
Quote:
|
|
#4
April 29th, 2015, 04:40 PM
|
||||
|
||||
|
Re: 292 engine pull
When I pulled the 292 out of my 64 I had the whole front clip off the truck(makes things alot easier), and be sure to find the bolts Under the rubber mounts on the engine...once those are off and the engine comes off the mounts...you only need to lift it about an inch...take your flywheel inspection cover off and take all the pressure plat bolts out 1 by one...have someone crank the engine over by hand so you can access the bolts from underneath...once the pressure plat is unbolted the engine will slide right out of the shaft without issue. Do be sure the tranny is in neutral just to help make things easier. Do all this while watching the oil pan distance between the cross member. Once out of the tranny lift straight up and have at it. lol What are your plans? Lopey cam and lump port head with sbc valves? I did a 292 so if you have questions PM me.
EDIT!!! Don't forget to unbolt the bell housing from the engine. lol My bad.
__________________
"Excuse the rust I use my truck" 1964 GMC 1500 305E/sm420 4 barrel intake mod and dual exhaust. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. 1964 Chevy C20 292/SM420 1966 Chevy C10 292 hotrod 6/TKO600 My youtube channel aka Military Chevy: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
|
|
#6
May 14th, 2015, 07:21 PM
|
||||
|
||||
|
Re: 292 engine pull
I actually pulled the motor out without the bell housing. Disconnected the clutch linkage from the block and unbolted the pressure plate and it slid right out. Bell housing was Much easier to pull with the engine out of the way.
__________________
"Excuse the rust I use my truck" 1964 GMC 1500 305E/sm420 4 barrel intake mod and dual exhaust. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. 1964 Chevy C20 292/SM420 1966 Chevy C10 292 hotrod 6/TKO600 My youtube channel aka Military Chevy: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
|
|
#8
May 15th, 2015, 05:51 AM
|
|||
|
|||
|
Re: 292 engine pull
It was much easier this way then when I took the whole thing out. Nice to be able to leave the clutch and everything in place!
|
|
#9
December 27th, 2015, 01:28 AM
|
||||
|
||||
|
Re: 292 engine pull
Hey, Any updates on this build?
__________________
"Excuse the rust I use my truck" 1964 GMC 1500 305E/sm420 4 barrel intake mod and dual exhaust. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. 1964 Chevy C20 292/SM420 1966 Chevy C10 292 hotrod 6/TKO600 My youtube channel aka Military Chevy: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
|
 |
| Bookmarks |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Re: [6066 GMC Truck] Pull engine? | Archiver | Previous Forum Posts | 0 | May 7th, 2002 02:58 AM |
| Re: [6066 GMC Truck] Pull engine? | Archiver | Previous Forum Posts | 0 | May 1st, 2002 08:04 AM |
| Re: [6066 GMC Truck] Pull engine? | Archiver | Previous Forum Posts | 0 | April 30th, 2002 01:26 AM |
| Pull engine? | Archiver | Previous Forum Posts | 0 | April 30th, 2002 01:14 AM |
| Re: [6066 GMC Truck] Pull engine? | Archiver | Previous Forum Posts | 0 | April 30th, 2002 01:08 AM |
