6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Interiors, Dash, Lights and Electrical
#Sponsored

Interiors, Dash, Lights and Electrical Everything Inside

Reply
 
Thread Tools
  #1  
Old December 21st, 2019, 09:11 PM
SCANTRON SCANTRON is offline
Junior Member
 
Join Date: Sep 2018
Location: Montclair, California
Truck: 1963 GMC 1000
Age: 34
Posts: 19
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 43
SCANTRON is on a distinguished road
Default Cab questions

I have a 63 cab and I have a question about the fresh air cab vents. I recently removed them to replace the gasket and repaint them upon removal I found the were being help in by double sided tape. My question is on the proper mounting is there a nut or clip for the back side
Attached Images
File Type: jpg IMG_20191201_145213579.jpg (1.81 MB, Multiple views, 8 clicks)
File Type: jpg IMG_20191201_145225755.jpg (728.1 KB, Multiple views, 6 clicks)
File Type: jpg IMG_20191201_145345392.jpg (1.64 MB, Multiple views, 4 clicks)
File Type: jpg IMG_20191201_145307731.jpg (477.5 KB, Multiple views, 2 clicks)
Reply With Quote
  #2  
Old December 22nd, 2019, 04:03 PM
Jeannie Jeannie is offline
Moderator
 
Join Date: Jan 2013
Location: OKC, Oklahoma
Truck: Shopping for a 1960-61 4x4
Posts: 357
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 166
Jeannie is on a distinguished road
Default Re: Cab questions

Moved to Interiors category.
Reply With Quote
  #3  
Old December 23rd, 2019, 04:34 AM
sclor's Avatar
sclor sclor is offline
Senior Member
 
Join Date: Jan 2013
Location: New Orleans, LA
Truck: 1966 GMC 1000 series fenderside
Posts: 203
Thanks: 1
Thanked 0 Times in 0 Posts
Rep Power: 131
sclor is on a distinguished road
Default Re: Cab questions

My cab is a 1966, but those vents were held in with sheet metal screws that went into that metal flange in the kick panel. Tape was likely a substitute for the gasket they used from the factory between vent and flange.

Hope that helps.
Regards
Steve
New Orleans
Reply With Quote
  #4  
Old December 24th, 2019, 07:56 PM
AZKen's Avatar
AZKen AZKen is offline
-= Dues Paid =-
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,647
Thanks: 0
Thanked 3 Times in 3 Posts
Rep Power: 527
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Re: Cab questions

I assume "they" means the gaskets? The tape was to hold the gasket on temporarily, I guess, to get plate installed. Four very tiny dabs of RTV will hold it.

The vent is held with sheet metal screws into a hole. As sclor said.

Is that your question?

Last edited by AZKen; December 24th, 2019 at 08:14 PM.
Reply With Quote
  #5  
Old December 25th, 2019, 03:39 PM
SCANTRON SCANTRON is offline
Junior Member
 
Join Date: Sep 2018
Location: Montclair, California
Truck: 1963 GMC 1000
Age: 34
Posts: 19
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 43
SCANTRON is on a distinguished road
Default Re: Cab questions

Yes, that was my question. Appreciate your help, I think I will be able reinstall the vents with confidence.
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Cab support and dimmer switch replacement questions. Archiver Previous Forum Posts 3 November 30th, 2012 12:46 AM
Re: [6066 GMC Truck] Re: Hey Guys and Gals? Questions, Questions, Questions :D Archiver Previous Forum Posts 0 March 28th, 2003 04:21 AM
Hey Guys and Gals? Questions, Questions, Questions :D Archiver Previous Forum Posts 0 March 27th, 2003 08:14 AM
Re: [6066 GMC Truck] Re: Hey Guys and Gals? Questions, Questions, Questions :D Archiver Previous Forum Posts 0 March 27th, 2003 12:44 AM
Re: Hey Guys and Gals? Questions, Questions, Questions :D Archiver Previous Forum Posts 0 March 27th, 2003 12:23 AM


All times are GMT +1. The time now is 04:24 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 831730222135|1729092277|0