Pay Dues or become a Site Supporter |
|
Transmissions and Rear Ends Three on the tree or four in the floor? Shift it all here. |
|
Thread Tools |
#1
|
|||
|
|||
Transmission cross member ??
Working on my 64 1000 305, sm420.
Will be removing the sm for some new bearings and synchros in the future, as well as new clutch disc, pressure plate and throw out. Doing a little pre inspection and see that the trans crossmember is riveted to the frame rails. To me it looks like there is not enough room to move the trans far enough back to clear the clutch without the rear of the trans contacting the crossmember. Have any of you had to drill the rivets and remove the crossmember to do a trans R&R?
__________________
Steve Stock Gig Harbor, Wa 1953 Chevrolet 3100 261 cu inch, SM420 Finished Cab off restoration 1964 GMC 1000 305 V6, SM 420 Restoration is now started, still looking for an oldsmobile style power steering pump |
#2
|
||||
|
||||
Re: Transmission cross member ??
Steve:
I removed a 1963 305 and sm420 from a riveted cross member style frame. They would not come out together. I believe we got the trans out by moving it back and sideways. Removing the rivets would be a good way but very difficult access for tools. Some cross members are bolted from the factory. We may have had the motor out when removing trans back/sideways and down thru the gap. If you run into an impossible situation, there are good nuclear options. Last edited by AZKen; March 4th, 2020 at 09:32 PM. |
#3
|
|||
|
|||
Re: Transmission cross member ??
I changed the Clutch on my '64 C-30 (should be the same or similar) and had no problem. Just take off the Hump Cover and you should have plenty enough room.
Edit: Now that I think of it I also change the Clutch in a '63 GMC 3/4 Ton once. There again, no problem.
__________________
Drove and owned many, but some of the more interesting ones were: -'60 GMC 2500 Dump, 305 V-6 -'62 GMC 4000 Flatbed, 305 V-6 -'62 GMC 6500 Flatbed Dump, 478 V-6 -'67 GMC 7500 Box, 6V-53 Detroit -'71 GMC 9500 Flatbed Dump, 637 V-8 |
#4
|
|||
|
|||
Re: Transmission cross member ??
Thank you sir(s)
Much appreciate the responses.
__________________
Steve Stock Gig Harbor, Wa 1953 Chevrolet 3100 261 cu inch, SM420 Finished Cab off restoration 1964 GMC 1000 305 V6, SM 420 Restoration is now started, still looking for an oldsmobile style power steering pump |
#5
|
||||
|
||||
Re: Transmission cross member ??
Bill T; "you should have plenty enough room." Plenty enough room for what?
|
#6
|
||||
|
||||
Re: Transmission cross member ??
there is no crossmember to remove--transmission hangs on bell housing. Simply remove floor pan, then driveshaft(with attached hanger bearing), parking/emergency brake cable(if underdash type like 1000 series), then 4 3/4" bolts. Grab transmission by the shift lever and work out away from the bell housing and lower to the floor. After setting the transmission on the floor, remove the gearshift retainer, take out the gearshift lever and the lever for the parking/emergency brake lever asm., and slide out from under vehicle. I hope this is of some assistance in this matter.
__________________
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. |
#7
|
|||
|
|||
Re: Transmission cross member ??
Thanks for the reply Lewis, I understand there isnt a trans cross member I should of said the cross plate that retains the parking brake bell crank, it is riveted to the frame rails and only a couple inches rearward of the sm420. Doesnt look like I can move the tranny back far enough to get the input shaft past the clutch disc.
__________________
Steve Stock Gig Harbor, Wa 1953 Chevrolet 3100 261 cu inch, SM420 Finished Cab off restoration 1964 GMC 1000 305 V6, SM 420 Restoration is now started, still looking for an oldsmobile style power steering pump |
#8
|
|||
|
|||
Re: Transmission cross member ??
Plenty enough room to change the Clutch, Pressure Plate, etc.
__________________
Drove and owned many, but some of the more interesting ones were: -'60 GMC 2500 Dump, 305 V-6 -'62 GMC 4000 Flatbed, 305 V-6 -'62 GMC 6500 Flatbed Dump, 478 V-6 -'67 GMC 7500 Box, 6V-53 Detroit -'71 GMC 9500 Flatbed Dump, 637 V-8 Last edited by BillT; March 5th, 2020 at 04:06 AM. |
#9
|
|||
|
|||
Re: Transmission cross member ??
Quote:
I also seem to remember just letting the tip of the pilot shaft rest on the edge of the bell, if you don't need to take the trans out. I mentioned "plenty enough room". There is plenty enough to get the job done without a whole lot of trouble.
__________________
Drove and owned many, but some of the more interesting ones were: -'60 GMC 2500 Dump, 305 V-6 -'62 GMC 4000 Flatbed, 305 V-6 -'62 GMC 6500 Flatbed Dump, 478 V-6 -'67 GMC 7500 Box, 6V-53 Detroit -'71 GMC 9500 Flatbed Dump, 637 V-8 |
#10
|
|||
|
|||
Re: Transmission cross member ??
Thanks Bill, I was looking at the raising of the back of the motor last night, that will do it for sure, Thank you for your help.
__________________
Steve Stock Gig Harbor, Wa 1953 Chevrolet 3100 261 cu inch, SM420 Finished Cab off restoration 1964 GMC 1000 305 V6, SM 420 Restoration is now started, still looking for an oldsmobile style power steering pump |
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rear cross Member mounts | melgd | Transmissions and Rear Ends | 0 | May 3rd, 2016 01:25 PM |
Re: [6066 GMC Truck] transmission cross member | Archiver | Previous Forum Posts | 0 | March 4th, 2002 02:03 AM |
Re: transmission cross member | Archiver | Previous Forum Posts | 0 | March 4th, 2002 01:53 AM |
Re: [6066 GMC Truck] transmission cross member | Archiver | Previous Forum Posts | 0 | March 4th, 2002 12:16 AM |
transmission cross member | Archiver | Previous Forum Posts | 0 | March 3rd, 2002 12:14 AM |