6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Transmissions and Rear Ends
#Sponsored

Transmissions and Rear Ends Three on the tree or four in the floor? Shift it all here.

Reply
 
Thread Tools
  #1  
Old May 7th, 2017, 06:29 AM
401bluebird 401bluebird is offline
Junior Member
 
Join Date: Oct 2016
Location: Ojai California
Truck: 1960 GMC chassis 401 V6 Bluebird coach
Posts: 13
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 54
401bluebird is on a distinguished road
Default RT 910 10 speed retrofit from 5 spd

High-
After years of waiting, I am about to refresh my GMC chassis 1960 Bluebird all American Motorhome conversion. My 401 GMC v6 is tight and runs well. It has a Clark 5 speed which doesn't offer enough gear choices for this marginally powered coach.

My friend, a diesel bus mechanic, suggested I find an Eaton/Fuller RT 910 road ranger 10 speed trans. Says they are very common and can be acquired for fairly cheap. It offers the obvious closer gear spreads, plus as a bonus, an overdrive final ratio; something I can really use.

My bus chassis has the large bell housing, which I am to believe is an SAE 2 size. Has anyone done such a swap before? My mechanic friend said that there are two basic shifting mechanisms, one is cable, the other is mechanical rods.

I appreciate any insights offered.
-Andy Carlson
Ojai CA
Reply With Quote
  #2  
Old May 7th, 2017, 05:24 PM
George Bongert George Bongert is offline
Senior Member
 
Join Date: Jan 2013
Location: Oshkosh Wisconsin
Truck: Former owner Repowered by GMC 305 V-6, 1963 Chevy 30 Series SM420 Long Bed (9') Step/Fenderside
Posts: 213
Thanks: 0
Thanked 1 Time in 1 Post
Rep Power: 145
George Bongert will become famous soon enoughGeorge Bongert will become famous soon enoughGeorge Bongert will become famous soon enough
Default Re: RT 910 10 speed retrofit from 5 spd

Quote:
Originally Posted by 401bluebird View Post
High-
After years of waiting, I am about to refresh my GMC chassis 1960 Bluebird all American Motorhome conversion. My 401 GMC v6 is tight and runs well. It has a Clark 5 speed which doesn't offer enough gear choices for this marginally powered coach.

My friend, a diesel bus mechanic, suggested I find an Eaton/Fuller RT 910 road ranger 10 speed trans. Says they are very common and can be acquired for fairly cheap. It offers the obvious closer gear spreads, plus as a bonus, an overdrive final ratio; something I can really use.

My bus chassis has the large bell housing, which I am to believe is an SAE 2 size. Has anyone done such a swap before? My mechanic friend said that there are two basic shifting mechanisms, one is cable, the other is mechanical rods.

I appreciate any insights offered.
-Andy Carlson
Ojai CA

Greetings 401bluebird!

I'm not sure what you will need to make this transmission swap, and the Fuller Roadranger 10 speed would be a good choice for your application. However, there is one drawback to the Fuller Roadranger transmission, that being that it is a non-synchronized transmission, (I assume your Clark 5 speed IS synchronized) meaning that you will have to learn how to double clutch when shifting from one gear to the next, or learn to shift gears without clutching by using engine RPMs. In most truck driving schools, it is recommended to double clutch these transmissions, but I know many over the road haulers who use the engine RPMs and no clutch method when shifting gears. I once drove a sweet corn truck for neighbor who taught me how to shift these transmissions without using the clutch, and they shifted as smooth as silk. I'll quote what he said to me as he taught me how to handle these transmissions: "We only use the clutch on these (Fuller Roadranger) transmissions for three things~~~stop, start, and back up"! This sounds like an interesting project! Good Luck!
Reply With Quote
  #3  
Old May 8th, 2017, 02:53 AM
BillT BillT is offline
Senior Member
 
Join Date: Jan 2013
Location: Moneta, VA
Truck: Drove and Owned Many
Posts: 301
Thanks: 1
Thanked 0 Times in 0 Posts
Rep Power: 154
BillT is on a distinguished road
Default Re: RT 910 10 speed retrofit from 5 spd

That is correct that you will be going from a synchronized to a non-synchronized, but the Road Ranger is just about my favorite trans. Also want to say that the RT 910 is not an Overdrive. I believe the RTO 910 is though, but verify that info to be sure.

By the way, I "always" use the clutch when driving one.
__________________
Drove and owned many, but some of the more interesting ones were:

-'60 GMC 2500 Dump, 305 V-6
-'62 GMC 4000 Flatbed, 305 V-6
-'62 GMC 6500 Flatbed Dump, 478 V-6
-'67 GMC 7500 Box, 6V-53 Detroit
-'71 GMC 9500 Flatbed Dump, 637 V-8
Reply With Quote
  #4  
Old May 8th, 2017, 06:36 AM
401bluebird 401bluebird is offline
Junior Member
 
Join Date: Oct 2016
Location: Ojai California
Truck: 1960 GMC chassis 401 V6 Bluebird coach
Posts: 13
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 54
401bluebird is on a distinguished road
Default Re: RT 910 10 speed retrofit from 5 spd

Hello again- I found some new info in my search for RT 910 10-speed transmissions. Seems that the 10th gear is 1:1 direct for the RT 910. The RTO 910 however has a 1:1 9th gear and a 0.81:1 overdrive 10th gear. However, it was mentioned that the RTO-910 used a bigger bell housing size, an SAE 3 (Instead of SAE 2 as my Bluebird coach uses.

So I found a bus conversion site where one respondent suggested a Road Ranger RT 9509, a 9-speed trans with similar torque rating as an RT 910 and an SAE 2 bell housing size. This trans has a deeper 1st gear, plus a taller overdrive, 0.79:1 in 9th gear. Though this trans has broader spreads in each gear change, this has to be a huge improvement over my 5-speed Clark transmission.

I will go to some Truck Centers this week to see what is out there. I am hoping that my 401 V6 likes the change! Regards, -Andy Carlson
Ojai CA
Reply With Quote
  #5  
Old November 28th, 2020, 03:08 AM
Nugget's Avatar
Nugget Nugget is offline
-= Dues Paid =-
 
Join Date: Nov 2020
Location: Springfield, MO
Truck: 1963 1000
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Nugget is on a distinguished road
Default Re: RT 910 10 speed retrofit from 5 spd

RT910 is a direct 10th gear, RTO910 is .81 overdrive. Also these transmission require an air supply to shift from low to high range. With a little practice the only time you need the clutch is taking off and stopping. These transmissions are larger physically so you should make sure it will fit under the floor.
__________________
63 GMC long bed stepside 401m
71 Chevy Longhorn 350 small block
68 Chevelle Nomad 406 small block
Reply With Quote
  #6  
Old November 28th, 2020, 03:14 AM
Nugget's Avatar
Nugget Nugget is offline
-= Dues Paid =-
 
Join Date: Nov 2020
Location: Springfield, MO
Truck: 1963 1000
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
Nugget is on a distinguished road
Default Re: RT 910 10 speed retrofit from 5 spd

I build transmissions and rear ends at our shop and my boss been trying to get me to try a 13 speed behind my 401. I have access to core transmissions cheap but an automatic sounds better to an old man like me.
__________________
63 GMC long bed stepside 401m
71 Chevy Longhorn 350 small block
68 Chevelle Nomad 406 small block
Reply With Quote
  #7  
Old November 29th, 2020, 05:30 AM
BillT BillT is offline
Senior Member
 
Join Date: Jan 2013
Location: Moneta, VA
Truck: Drove and Owned Many
Posts: 301
Thanks: 1
Thanked 0 Times in 0 Posts
Rep Power: 154
BillT is on a distinguished road
Default Re: RT 910 10 speed retrofit from 5 spd

Good point about the Air Pressure. I forgot to consider that when we were talking 3 years back, lol.

Air Pressure shouldn't be that much of a problem though. A small aftermarket unit should even do fine.
__________________
Drove and owned many, but some of the more interesting ones were:

-'60 GMC 2500 Dump, 305 V-6
-'62 GMC 4000 Flatbed, 305 V-6
-'62 GMC 6500 Flatbed Dump, 478 V-6
-'67 GMC 7500 Box, 6V-53 Detroit
-'71 GMC 9500 Flatbed Dump, 637 V-8
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
RE: [6066 GMC] NV4500 Retrofit......DOCUMENTED, yee haw Archiver Previous Forum Posts 0 November 17th, 2008 02:43 PM
Re: NV4500 Retrofit......DOCUMENTED, yee haw Archiver Previous Forum Posts 0 November 16th, 2008 01:10 AM
RE: [6066 GMC] NV4500 Retrofit......DOCUMENTED, yee haw Archiver Previous Forum Posts 0 November 16th, 2008 01:08 AM
Re: [6066 GMC Truck] Crazy Question - Retrofit Automatic to a 4x4? Archiver Previous Forum Posts 0 October 5th, 2001 07:52 AM
Crazy Question - Retrofit Automatic to a 4x4? Archiver Previous Forum Posts 0 October 4th, 2001 02:55 AM


All times are GMT +1. The time now is 07:17 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 891731258770|1730225848|0