6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Transmissions and Rear Ends
#Sponsored

Transmissions and Rear Ends Three on the tree or four in the floor? Shift it all here.

Reply
 
Thread Tools
  #1  
Old January 27th, 2022, 03:50 PM
TRybas TRybas is offline
-= Dues Paid =-
 
Join Date: Apr 2020
Location: Croydon, PA
Truck: 1960 GMC Long fleet 4x4
Age: 37
Posts: 47
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 46
TRybas is on a distinguished road
Default Lowering differential gear ratio. Dana 44

Looking for some guidance/ confirmation from anyone that has changed out the ring and pinion to get a little more high end out of the old girl. I’ve read through what I could find here and have talked to Jake about his setup. Not trying to get in a debate here about them being old work horses not meant for speed yada yada yada. Please keep it to the mechanics.

Seems doable than I got to reading somewhere about different thickness gears so I called spicer tech support to confirm. The gentlemen from spicer seemed knowledgeable and said to go lower than 3.92 (current setup) I would have to change out the carrier as well which they do not offer.

My goal is to be able to cruise around 60-65mph. My current set up is 1960 V6 305A 4-wheel-drive with an SM420. Dana 44 front and back at 3.92.

I was looking at the 3.54 part# 22856-5x or the 3.31 part# 706017-2x. Obviously my truck is 4x4 so I’d have to do both front and rear. Could get pricey and I don’t want to start pulling things apart to find I didn’t order the right stuff. If someone could confirm they have done so and specific parts it would be greatly appreciated.

I’ve also considered putting a gear vendor overdrive so I gave them a call. Their bolt on over drive is 14” long (and back ordered for several months). Taking 14” out of the drive shaft would put it at a pretty sharp angle. Not sure I am comfortable doing that. (See pics) Thoughts?

Regards, T.J.
Attached Images
File Type: jpeg E3AC1C41-DAE0-46A3-BBF4-FFF3807BC6BC.jpeg (2.97 MB, Multiple views, 8 clicks)
File Type: jpeg E54DF447-AC74-4579-94B6-7AAD5FDA114B.jpeg (2.91 MB, Multiple views, 4 clicks)
Reply With Quote
  #2  
Old January 28th, 2022, 02:10 AM
Ed Snyder's Avatar
Ed Snyder Ed Snyder is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Medford, Oregon
Truck: 1962, 1967
Posts: 889
Thanks: 0
Thanked 5 Times in 3 Posts
Rep Power: 351
Ed Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura about
Default Re: Lowering differential gear ratio. Dana 44

Quote:
Originally Posted by TRybas View Post
Looking for some guidance/ confirmation from anyone that has changed out the ring and pinion to get a little more high end out of the old girl.

Seems doable than I got to reading somewhere about different thickness gears so I called spicer tech support to confirm. The gentlemen from spicer seemed knowledgeable and said to go lower than 3.92 (current setup) I would have to change out the carrier as well which they do not offer.

My goal is to be able to cruise around 60-65mph. My current set up is 1960 V6 305A 4-wheel-drive with an SM420. Dana 44 front and back at 3.92.

I was looking at the 3.54 part# 22856-5x or the 3.31 part# 706017-2x. Obviously my truck is 4x4 so I’d have to do both front and rear. Thoughts?

Regards, T.J.
My '62 Suburban came from the factory with 3.92 gears. Prior to my purchase 25 years ago, someone had changed the rear gears to 3.54, but neglected to do anything with the front end. I found that out after driving it 1300 miles from Phoenix, AZ, and attempting to drive up my steep gravel driveway. After I locked in the hubs and put the T-case in 4 high, the truck refused to move forward more than a few inches. That's when I realized the mis-match in gears. I had a local 4x4 shop change the front to 3.54 to match the rear. With 32" tall tires I have no problem with freeway cruising. It turns 2600 RPM at 70 MPH.
__________________
Ed Snyder
Medford, Oregon
1962 1000 Pickup 401M & Muncie 318 with overdrive
1962 K1000 Suburban 401M & SM420
1967 CM1500 pickup 351E & NP435
Reply With Quote
  #3  
Old February 7th, 2022, 06:58 PM
duallyjams's Avatar
duallyjams duallyjams is offline
Member
 
Join Date: Jan 2013
Location: Deale
Truck: 64 GMC
Posts: 31
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 81
duallyjams is on a distinguished road
Default Re: Lowering differential gear ratio. Dana 44

A lot of good info here http://www.billavista.com/index.html

To my knowledge the same carrier works with 4:10 and down, so if your going from 3:92 to 3:54 you should be able to use the same carrier.
__________________
63 GMC V6 carryall
64 GMC V6 LWB
66 GMC SWB BBW buddy buckets
Reply With Quote
  #4  
Old October 28th, 2023, 01:35 AM
Chuck78 Chuck78 is offline
Member
 
Join Date: Jul 2014
Location: Columbus OH
Truck: 1962 GMC 1000 panel truck
Age: 46
Posts: 90
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 86
Chuck78 is on a distinguished road
Default Re: Lowering differential gear ratio. Dana 44

Quote:
Originally Posted by TRybas View Post
Looking for some guidance/ confirmation from anyone that has changed out the ring and pinion to get a little more high end out of the old girl.


I got to reading somewhere about different thickness gears so I called spicer tech support to confirm. The gentlemen from spicer seemed knowledgeable and said to go lower than 3.92 (current setup) I would have to change out the carrier as well which they do not offer.

My goal is to be able to cruise around 60-65mph. My current set up is 1960 V6 305A 4-wheel-drive with an SM420. Dana 44 front and back at 3.92.

I was looking at the 3.54 part# 22856-5x or the 3.31 part# 706017-2x. Obviously my truck is 4x4 so I’d have to do both front and rear.


Regards, T.J.

From what I've read looking around at Dana 44 info, there is a split with the carriers. One carrier fits 3.73 / 3.55 / 3.31 / 3.07 / etc gears, the other fits 3.92 & higher numerical gears.



This isn't much in our interest unless running tall 4x4 tires, but you CAN buy special thicker gears to run a 3.92 & up numerically on the 3.73 - 3.07 etc carriers.

The one thing about the older GMC Dana 44s that the carrier bearings are a slightly different size then most newer Dana 44s. I believe ours also use the fine spline, I believe it's a 30 spline axle shaft?

I have a 2wd 1962 GMC 1000 Panel Truck with I believe from my notes 10 years ago is a 3.07 ratio Dana 44. I'd like to keep it a 2wd for fuel MPG purposes although a 4x4 panel truck would be very cool... But I have a Suzuki Samurai LWB TDI swap project for a 4WD rig...

I'd really like to be able to pull dirtbikes on a trailer up steep gravel forest service roads, so it'd be nice to run a Detroit TrueTrac or Nitro Helix limited slip torsen worm gear lockup type limited slip unit. I'll have to look into this to see what it takes to swap to a TrueTrac or Nitro Helix carrier.

The other option is I believe Honda Passport / Isuzu Rodeo Dana 44 rear axles are 6 lug and about the same dimensions wheel mounting surface to wheel mounting surface. Perhaps rear disc even.

But I welded shut my lug holes and drilled my axles to 5 on 5" lug pattern to match a nice set of wheels I got and to match the 76-91 Suburban 5 lug disc brake coil spring front crossmember that I got to swap to disc brakes & have common and affordable front end parts.
So I'd either have to have a special rear axle for 5 lugs, or buy special aftermarket front rotors to run 6 lugs on the disc brakes, but then I could use the same wheels as my Suzuki Samurai with Toyota axles or the 1988 Toyota 4WD pickup. All same 6 on 5.5".

Now that I realized I can ratchet strap the front suspension down on my dirt bike about 3" more than it sits when I'm seated on the bike, and be able to stuff it into the back of the panel truck, I'm a lot more interested in getting this thing set up as a nice highway cruiser with a limited slip rear differential. Dodge Dakota V6 Magnum (& '87-'98-ish Jeeps) 2wd AX-15 transmission with 3.83/2.33/1.44/1.00/0.79 ratios should give me a really great fuel economy at 55 mph on 3.07's or 3.31's, even 3.55's, and will do decent enough at 70mph. The current 3.34 1st gear Saginaw struggles a little off the start on 28" tires & 3.07 diff ratio, but a 3.83 1st gear should do quite well. 3.55 would be ideal off the line but if I run the low miles GMC 351C big block V6 that I've got instead of the stock 305D, I'm going to have tons of off idle torque and will be wanting to do everything to keep the RPM down for fuel economy...
3.07 & 28" tires on an AX-15 0.795:1 overdrive 5th puts 1600RPM right at 55mph, and 1600rpm is where the 305D and 351C make their peak torque (& generally peak torque RPM = peak fuel efficiency RPM), so switching to the 351C makes most sense with 3.07 gears. 70mph = 2050rpm. Fuel miser gearing with the torquey low rpm medium duty commercial truck engine!

3.07 & 3.31 & 3.55 gears are fairly readily available, FYI. 3.42 are not common.
If you have a 3.92 differential, that's probably the lowest you can go numerically without switching carriers.


I thought about swapping a VW 2.0TDI turbodiesel engine, that'd do great with 3.73's, but still wouldn't get any better than 33mpg tops. If I could get 23mpg on the 3.07 diff with the 0.79:1 overdrive 5th gear AX-15 transmission, that would be close enough, diesel costing $1 more per gallon would mean it would cost the same per mile at 25 miles per gallon gasoline versus 33 miles per gallon diesel. So I guess keeping the 900 lb big block V6 is it then! Upgrading to a lower miles 351C from a forward cab stake bed truck over my 277,000 mile 305D... I hope the used engine is as good as it was stated to be!
Attached Images
File Type: gif Carrier-Illustration.gif (26.8 KB, Multiple views, 10 clicks)
__________________
Chuck in Ohio
*'62 GMC 1000 Panel Truck - 305D/Saginaw 4sp soon: 351C V6 + AX15 5sp OD trans, & 73-87/91 disc brake front end, rear Cadillac calipers/ AWD Astro rotors, Dana 44 redrilled to 5 lug
*'88 Suzuki Samurai 4x4 project, VW 1.9L mTDI turbodiesel, Toyota V6 LandCruiser drivetrain, full floater axles, future LWB bed stretch
*'77-'79 Suzuki GS motorcycles, '76 Rickman CR900 roadracer.
*Dirtbikes: 2 Kawasaki KDX220R's, '77 Suzuki PE250, '83 PE175

Last edited by Chuck78; October 28th, 2023 at 01:55 AM.
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Dana 44? jastamjas Transmissions and Rear Ends 11 May 23rd, 2020 04:43 AM
Parting out 305E, SM420, Rockwell Tcase, Dana 44 & Dana 60 Larry 1960-1966 GMC Marketplace 5 October 1st, 2015 05:11 AM
dana 44 Archiver Previous Forum Posts 0 August 31st, 2009 01:14 AM
dana 44 Archiver Previous Forum Posts 0 March 22nd, 2008 01:38 AM
Re: [6066 GMC Truck] SM420 Speedo Gear Teeth vs Dana 44 Axle Ratio Archiver Previous Forum Posts 0 January 24th, 2003 07:50 AM


All times are GMT +1. The time now is 10:28 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 861730414881|1729330122|0