6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > GMC V6 and V12 Engines
#Sponsored

GMC V6 and V12 Engines Engine repair and rebuilding

Reply
 
Thread Tools
  #11  
Old April 17th, 2015, 06:51 AM
WE7X WE7X is offline
Member
 
Join Date: Sep 2013
Location: Issaquah, Washington
Truck: 1970 GMC RM-7500 based Motorhome
Posts: 80
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 92
WE7X is on a distinguished road
Default Re: Allison 6 Speed GMC 401

For something like 15 years, I have had an Allison AT from a 6500 or 7500 chassis. Would that likely be an MT40? I know I received a cable shifter assembly with it, that is about 25 feet too short for my rear engine configuration.
If I recall correctly, I was told it would have been a 5 speed, but I am not sure. Were they five speed, or six?

The plan back then, was to put it into my RM7500 'Motorhome', along with a 478M; to replace my 401M and the 5x2 Manual transmission. No progress yet, on that plan.
Rod J
Issaquah, WA
Reply With Quote
  #12  
Old April 23rd, 2015, 03:12 AM
tommr tommr is offline
Member
 
Join Date: May 2013
Location: phila pa
Truck: 1947 Flxible Clipper Bus 29 passenger 401 M
Posts: 76
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 90
tommr is on a distinguished road
Default Re: Allison 6 Speed GMC 401

Flexplate assembly from Bendtsens. consists of a GM factory plate from an old MT40 application. Bob shaved the face and drilled it for a factory Allison adapter ring. Then he machined a center pilot assembly to center the torque converter hub into the center of the plate. All very nice and very precise. fits like a glove. Don't think anybody else on the planet had these parts and the exp on the GMC V6. Glad I found him. Driveshaft is being built this week. All new Spicer yokes, tubes and axle companion flange. Gonna be a nice piece.
Attached Images
File Type: jpg 100_6323.JPG (2.84 MB, Multiple views, 11 clicks)
File Type: jpg 100_6324.JPG (2.89 MB, Multiple views, 8 clicks)
File Type: jpg 100_6325.JPG (2.98 MB, Multiple views, 7 clicks)
File Type: jpg 100_6326.JPG (3.80 MB, Multiple views, 6 clicks)
File Type: jpg 100_6328.JPG (2.37 MB, Multiple views, 5 clicks)
Reply With Quote
  #13  
Old April 24th, 2015, 07:24 AM
BobBray BobBray is offline
-= Dues Paid =-
 
Join Date: Feb 2013
Location: Los Angeles, CA.
Truck: 1967 CM 2500
Posts: 261
Thanks: 3
Thanked 3 Times in 2 Posts
Rep Power: 156
BobBray will become famous soon enoughBobBray will become famous soon enough
Default Re: Allison 6 Speed GMC 401

That's a very nice Flxible (yes, I spelled it right) Clipper you have there! Many of those were built with Buick straight 8 engines and were converted to GMC V-6 power in the 60's. I have a friend with a Clipper that has a 478 in it. Good luck, hope you get it back on the road soon. It's a light bus and it should really fly.
Reply With Quote
  #14  
Old April 24th, 2015, 12:41 PM
tommr tommr is offline
Member
 
Join Date: May 2013
Location: phila pa
Truck: 1947 Flxible Clipper Bus 29 passenger 401 M
Posts: 76
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 90
tommr is on a distinguished road
Default Re: Allison 6 Speed GMC 401

Yes ours had a 320 Buick inline 8 originally. It was converted to the V6 in 1971. Gonna be interesting to see how well it pulls 5th. The 478 would be unbelievable in a Flx. Tom
Reply With Quote
  #15  
Old April 24th, 2015, 12:45 PM
tommr tommr is offline
Member
 
Join Date: May 2013
Location: phila pa
Truck: 1947 Flxible Clipper Bus 29 passenger 401 M
Posts: 76
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 90
tommr is on a distinguished road
Default Re: Allison 6 Speed GMC 401

youtube.com/watch?v=itSs8SYvpbM Might have posted this before.
Reply With Quote
  #16  
Old May 3rd, 2015, 01:44 PM
abus319 abus319 is offline
-= Site Supporter =-
 
Join Date: Sep 2013
Location: Austin Texas
Truck: 1960 3500, 305D heads
Posts: 116
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 98
abus319 is on a distinguished road
Default Re: Allison 6 Speed GMC 401

I have to admit there are some big gaps in my mechanical knowledge and automatics definitely fall into that category.
I have been puzzling over the bolt/ hole setup on the center pilot assembly. I assume that the 6 countersunk holes are for the crank thru bolts. Are the other 6 holes threaded, I can't tell for certain?
h
Reply With Quote
  #17  
Old May 3rd, 2015, 07:20 PM
tommr tommr is offline
Member
 
Join Date: May 2013
Location: phila pa
Truck: 1947 Flxible Clipper Bus 29 passenger 401 M
Posts: 76
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 90
tommr is on a distinguished road
Default Re: Allison 6 Speed GMC 401

correct those are thru bolts to the crank. the other holes are threaded and not used for this app. Bob must have been repurposing something he had in inventory. thx.
Reply With Quote
  #18  
Old May 14th, 2015, 05:25 AM
abus319 abus319 is offline
-= Site Supporter =-
 
Join Date: Sep 2013
Location: Austin Texas
Truck: 1960 3500, 305D heads
Posts: 116
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 98
abus319 is on a distinguished road
Default Re: Allison 6 Speed GMC 401

Cant wait to see pics of your progress.
Reply With Quote
  #19  
Old July 17th, 2015, 11:15 PM
tommr tommr is offline
Member
 
Join Date: May 2013
Location: phila pa
Truck: 1947 Flxible Clipper Bus 29 passenger 401 M
Posts: 76
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 90
tommr is on a distinguished road
Default Re: Allison 6 Speed GMC 401

Did 4,000 miles in 23 days. the 401 needed 2 qts of oil and aside from a load of separated gas ran great. The Allison 1000 operated perfectly. 60 mph is 2100 rpm instead of 2800 rpm with the non synchro non overdrive 4 spd Spicer. Got an astounding high of 9.5 mpg on mostly flat highway only runs of 350 miles. Highway only was 8 mpg with the old trans. Not the jump I thought I would get with the rpm reduction but even the prior 8 was very good. Combined highway/city was low 7s. Used the biggest Griffin trans cooler they make and never ran more than 170 degrees. The 401 is still very able but slow in the big hills. pulled a crazy steep hill up to an overlook in 1st gear at 2400 rpm. The guy behind us couldn't believe we made it. The bus felt like it could have pulled it all day as long as youre not in a hurry. Tom
Attached Images
File Type: jpg 100_5882.JPG (2.80 MB, Multiple views, 3 clicks)
File Type: jpg 100_6088.JPG (2.65 MB, Multiple views, 5 clicks)
File Type: jpg 100_6352.JPG (2.63 MB, Multiple views, 6 clicks)
File Type: jpg 100_6353.JPG (2.77 MB, Multiple views, 4 clicks)
File Type: jpg 100_6393.JPG (2.71 MB, Multiple views, 7 clicks)
Reply With Quote
  #20  
Old July 17th, 2015, 11:55 PM
turbobill turbobill is offline
Member
 
Join Date: Feb 2013
Location: northern NY when not flying
Truck: 1968 HM80 with a 478M and a few engines plus a Toro-Flow
Posts: 99
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 97
turbobill is on a distinguished road
Default Re: Allison 6 Speed GMC 401

Nothing wrong with the hill climbing ability that a turbocharger won't fix! That's the only device that makes diesels powerful.
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
401 V6 with New Venture 5-speed transmission GMC Guy GMC V6 and V12 Engines 2 February 21st, 2013 02:07 AM
Re: [6066 GMC] 401 Engine Speed Archiver Previous Forum Posts 0 January 7th, 2010 12:00 AM
401 Engine Speed Archiver Previous Forum Posts 0 November 29th, 2009 12:08 AM
Re: 1961 3/4 ton 305 v6 4 speed hydromatic allison Archiver Previous Forum Posts 0 June 27th, 2002 02:24 AM
1961 3/4 ton 305 v6 4 speed hydromatic allison Archiver Previous Forum Posts 0 June 25th, 2002 01:54 AM


All times are GMT +1. The time now is 12:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 841730414881|1729207883|0