Pay Dues or become a Site Supporter |
|
GMC V6 and V12 Engines Engine repair and rebuilding |
|
Thread Tools |
#11
|
|||
|
|||
Re: 305D V6 rebuild parts ? buyable ? ? Custom made ? ? ?
I emailed them almost a week ago about a REO 331 rebuild kit out of curiosity.
Haven't heard a thing back from them yet. Mike |
#12
|
||||
|
||||
Re: 305D V6 rebuild parts ? buyable ? ? Custom made ? ? ?
My reply was next day so I'd call them or send it again. They seemed really nice and helpful.
|
#13
|
|||
|
|||
Re: 305D V6 rebuild parts ? buyable ? ? Custom made ? ? ?
I resent my email, it was last Thursday I sent it off. So its been 5 days anyway so I will see if I get a reply from them this time.
You'd think if they had nothing they would tell a guy ? ! Mike |
#14
|
||||
|
||||
Re: 305D V6 rebuild parts ? buyable ? ? Custom made ? ? ?
I'll bet Kanter is probably more keen to talk on the phone than answer emails.
__________________
1960 GMC Suburban -305A (Soon to be 351E) & SM-420 (2nd Owner) 1978 Chevy Silverado - 350 DIESEL & T400 w/ overdrive (2nd Owner) Suburban build thread on 67-72chevytrucks site: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. |
#15
|
|||
|
|||
Re: 305D V6 rebuild parts ? buyable ? ? Custom made ? ? ?
Just spoke to Kanter yesterday. I want to rebuild the 305E in my truck. The salesman was excellant, but informed me that thay did not have any pistons and didn't know when they would get any in.
I realy concerned now. I have a knock in the lower end of my engine and want to tear it down to investigate. If I need pistons, I have no idea what I'm going to do. Any one have any ideas? Joe |
#16
|
||||
|
||||
Re: 305D V6 rebuild parts ? buyable ? ? Custom made ? ? ?
Have you contacted EGGE? They seem to have quite a bit of piston variety and can possibly MAKE pistons for you. I was lucky, I found a '66 GMC 305E that had been run on propane since the day it was purchased. Clean inside and performs like new. Just need to get the truck away from the painter!
Last edited by Andice; March 27th, 2013 at 01:43 AM. |
#17
|
|||
|
|||
Re: 305D V6 rebuild parts ? buyable ? ? Custom made ? ? ?
Joe, you may want to try some of the forklift engine rebuilders for pistons, most likely they would want your engine for the rebuild. Try "All Forklift Parts" (909-356-1771) for a Hyster 305 V6. Another would be "Budget's Forklift Engines" (800-821-3796). The Hyster application is basically a 305C V6, 4 rings per piston and don't worry about the extra ring because even GMC superceeded the 3 ring application in the early 70's for standardization purposes in 305E replacement pistons.
|
#18
|
|||
|
|||
Re: 305D V6 rebuild parts ? buyable ? ? Custom made ? ? ?
For pistons you might want to take a look here:
http://webpages.charter.net/beckracing/slvpg55.htm I have used this brand (Silvolite) before with complete satisfaction, but it wasn't in a V-6. Ray |
#19
|
||||
|
||||
Re: 305D V6 rebuild parts ? buyable ? ? Custom made ? ? ?
Quote:
He describes rebuilding small blocks just as you describe. He makes a pretty good case and describes what he looks for and what he tosses out. Now there are piles of small block parts out there to go through, unlike our V6. I would rather have all new stuff too, but I don't think anyone is going to repop any of it. All the parts numbers of parts that were being made a few years ago have just evaporated.
__________________
Jon S Las Vegas Nv 1966 GMC Suburban 305 V6 |
#20
|
|||
|
|||
Re: 305D V6 rebuild parts ? buyable ? ? Custom made ? ? ?
Is anyone running a Duramax? Or a 6.5 chevy diesel. Each piston is fit to the cylinder individually. There is quite a range of sizes. The bottom of the block is stamped A,B,C at each journal for the piston size. Also ford and GM put individual oversized pistons and undersized bearings in new engines. Chrysler probably did to but I have not seen it. Personally I save all unusual oversize piston I find. Remember Its all about the clearances.
|
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Custom made Dist. for the V-6 on ebay | Archiver | Previous Forum Posts | 0 | July 16th, 2008 03:25 AM |
Custom Made HEI Distributor Spacer/Sleeve | Archiver | Previous Forum Posts | 0 | May 26th, 2006 10:08 AM |
RE: [6066 GMC] Custom Made HEI Distributor Spacer/Sleeve | Archiver | Previous Forum Posts | 0 | May 26th, 2006 01:34 AM |
RE: [6066 GMC] Custom Made HEI Distributor Spacer/Sleeve | Archiver | Previous Forum Posts | 0 | May 12th, 2006 01:40 AM |
Custom Made HEI Distributor Spacer/Sleeve | Archiver | Previous Forum Posts | 0 | May 11th, 2006 11:08 AM |