6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Builds and Journals
#Sponsored

Builds and Journals This is where the magic happens. Photograph & document your GMC build progress for posterity.
NOTICE - Photobucket will delete your pics after a time. Use another host if possible.

Reply
 
Thread Tools
  #221  
Old October 7th, 2013, 04:56 PM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,779
Thanks: 19
Thanked 4 Times in 3 Posts
Rep Power: 569
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)

Before finding the wayward driveshaft I mentioned that I dropped the Rockwell T221. Here's how I did it.

First, I disconnected all of the drive shafts. There are two "U" bolts on every shaft with four nuts on the end of them. IIRC they're 1/2 inch bolts.

The rear shaft



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?



The input shaft that goes to the transmission



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?



And the front shaft



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Sorry for the pic quality. The camera got smudged and I didn't notice till I was copying the pics over.

The Ubolts probably won't just fall out once you get the nuts off. You can bang them with a hammer (put the nut back on a little so you don't buggar them up!) or use a big screwdriver to pry them off.

And you should tie or prop up the input shaft so it doesn't pull on the new gasket you put in and cause a leak later.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Take the cotter pin out of the shift linkage at the two points on the transfer case. Then pound the pin out with a hammer. I always put it back in afterwards (and the cotter pin) so it doesn't get lost.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Unscrew your speedometer cable



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

__________________
Step by steps:

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Some people are like slinkys. Not worth much but funny as heck when pushed down stairs.
__________________
If the women don't find you handsome, they should at least find you handy.
Reply With Quote
  #222  
Old October 7th, 2013, 05:07 PM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,779
Thanks: 19
Thanked 4 Times in 3 Posts
Rep Power: 569
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)

Drain the oil so you loose a little weight.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







To get the bolts out I had to go out and grab a $30.00 set of sockets from Autozone. On one hand I thought, dang that's $30.00 I didn't plan on spending. On the other hand....New tools!

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?






To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?





To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







My transfer case fluid was a healthy chocolate milk color. I dont think it came from the factory like that.

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?





To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

__________________
Step by steps:

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Some people are like slinkys. Not worth much but funny as heck when pushed down stairs.
__________________
If the women don't find you handsome, they should at least find you handy.
Reply With Quote
  #223  
Old October 7th, 2013, 05:44 PM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,779
Thanks: 19
Thanked 4 Times in 3 Posts
Rep Power: 569
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)

Stick a jack under the transfer case because it's HEAVY.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?








Then unscrew those 15/16 bolts from the passenger side. this was one of the pics that was messed up but they're huge bolts you can see by just squatting down and looking under the truck. Very easy to spot.
They're very short bolts too so don't get crazy.


Now take the bracket bolts loose where it connects to the emergency brake. there's two bolts on the rear, two underneath. You can see the bolt holes they came out of right above the bolts in my hand.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Another pic that messed up is the underneath bolts. When you take these out the tranny will try to fall. Make sure you put the plug in the drain hole and that the transfer case is braced up by the jack!

It will try to twist too, be careful.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?






When it's out pick the dirt dobber nests off. Mine had something like concrete on it too. not sure what that came from. I had to chisel it off with a screwdriver.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?








Anyway, that's it for removal. I hosed mine off with a pressure washer after washing the inside of my garage from the tranny repair. Both were a hot mess.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

__________________
Step by steps:

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Some people are like slinkys. Not worth much but funny as heck when pushed down stairs.
__________________
If the women don't find you handsome, they should at least find you handy.
Reply With Quote
  #224  
Old October 8th, 2013, 05:37 PM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,779
Thanks: 19
Thanked 4 Times in 3 Posts
Rep Power: 569
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)

I know most of you guys won't have (or be interested in) a 4x4 so this part might be kinda boring for ya. I'll try to hurry it along.

Today I ordered a pieced together rebuild kit from Rock Auto for about $113.00. The only kits I found online complete were almost $300

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?


I ain't spending that. I have a budget here!



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Here's my shopping list. I'll edit it if they arrive and dont fit or I missed anything:

The Seals:
  • Input Shaft Seal SKF Part Number #15655
  • Output Shaft Seal National Parts #472164 (x2)
  • Shift Shaft Seal SKF Part Number #7440 (x2)

The Bearings/Sleeves:
  • Rear Output Shaft Bearing (Cupped) SKF Part Number #BR15126
  • Front Outer Bearing National Parts #207L
  • Front Inner Bearing National Parts #209L
  • Rear Bearing Sleeve National Parts #15245
  • Front Bearing Sleeve SKF #BR14276
  • Main Shaft Pilot Bearing SKF #JH1612



Next up, the teardown dun dun DUNNN!!!



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

__________________
Step by steps:

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Some people are like slinkys. Not worth much but funny as heck when pushed down stairs.
__________________
If the women don't find you handsome, they should at least find you handy.
Reply With Quote
  #225  
Old October 10th, 2013, 06:23 AM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,779
Thanks: 19
Thanked 4 Times in 3 Posts
Rep Power: 569
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)

I spent the last two days cleaning up from the tranny rebuild. It looked like a bunch of dirty grease gremlins had a night of drunken debauchery in my tools. Eww.

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?





To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?




To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







So I rubbed them down with a roll of paper towels and some mineral spirits. That stuff is good for cleaning grease. The little square (3ft by 2ft or so) of plywood that I put on my bench to keep it from the worst of the paint, dirt and grease was so bad I had to take it outside and wire-wheel it to get it usable again. That got me started on wanting to wire wheel more stuff so I put all of my U-Joints in the carb cleaner for a two hour soak.

Then the FEDEX truck showed up with half of my seals. WTG Rock Auto!

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?





To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







I put them away then remembered my NOS muffler I got a few months ago. It's got a cheesy chick on it trying to look all shy. I don't know what that has to do with mufflers.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







I tried to slide it on myself. It has a larger side on the intake that fits right over my existing exhaust bits, but I cant get it to stay on with just sliding it on. it falls off when I start the truck. It sounded pretty good while it was on though. Still throaty but without the loud thunderous knock. I put it away again for now.

I moved back in the garage and touched up the step supports with more herculiner.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Put my old pressure plate, clutch, throwout and pilot bearings on a shelf. I can't throw them away yet. Hoarder!



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Then I pulled the Ubolts out of the carb cleaner bath and put them on paper towels to drip while I wipe them down. The powder puff stepped up then and noticed something I didn't.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Did you see it? Here's a closeup



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Yep, that's a smiley face! Powder Puff said, "daddy, this is probably the happiest job you have ever done on Cecilia, huh?"

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?


Gotta love how kids' minds work. I wire wheeled them all down then sprayed them with Ospho. I'm sure you can guess where I'm going with them.

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?




While they soak and convert I turned to my transfer case. I wire wheeled on it a little more but it's nasty stuff was still too hard. Instead I sprayed it with more Super Clean. Then I took off the side bracket.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Here's a pic of the bolt with all the pieces on it in order for reference. They didn't put any drain holes in the bracket so the metal spacer sits in water all the time. It corrodes to the bracket. I had to break mine loose with a hammer on one side.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?






And that was it for the day. Piddling stuff really, but it all needed doing. Here's to a good healthy cleanup and taking one more bite out of the elephant!

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

__________________
Step by steps:

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Some people are like slinkys. Not worth much but funny as heck when pushed down stairs.
__________________
If the women don't find you handsome, they should at least find you handy.
Reply With Quote
  #226  
Old October 21st, 2013, 08:27 PM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,779
Thanks: 19
Thanked 4 Times in 3 Posts
Rep Power: 569
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)

Sorry for the lack of updates guys. It got c*o*l*d here so I've been out of the truck mood lately. I guess I got too quiet because I got other members kickin me in the butt to get an update

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?


I love this place

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?



Here's what I did while I wasn't working on Cecilia.

Got a junk 4wheeler someone was done with for ...wait for it....



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?




Oh yeah!

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?



This is what I hope it will look similar to some day:



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Right now it looks like that rolled in dirt and razor blades. And the gas line is cut. Cecilia has given me confidence that I can at least try to make it putter around for the kids. All you need are good bones, right?

Then I did this (stick):



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?





So i could try to build this before winter hits hard



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







Steel is expensive. And I might be getting into more than I can handle, but I thought the same thing with Cecilia. I'm learning that once you get your hands into mechanical stuff they're all pretty simple concepts until you get wires involved. There's no magic there after all. Who knew!?

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?



So after all that we took a break to do this:



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?







yep, that's 8 points buddy! The redhead was a happy camper and we'll have some meat in the freezer for jerky and stew. Nom nom nom.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?




It's been a good time, but ya'll are right. I haven't done any truck stuff. I've got limited time to put the log splitter together (borrowed welder) so it'll be a little while till I get trucky again. I'll have alot of the splitter put together next weekend and the following weekend. It's gonna get colder pretty quick though and when it does I'll be done outside till spring, just a heads up. Like molasses I dont move much when it gets below 60 degrees. Brrr!
__________________
Step by steps:

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Some people are like slinkys. Not worth much but funny as heck when pushed down stairs.
__________________
If the women don't find you handsome, they should at least find you handy.
Reply With Quote
  #227  
Old October 22nd, 2013, 02:43 AM
BarryGMC BarryGMC is offline
Banned
 
Join Date: Jan 2013
Location: Banned City
Truck: None. Sold them all and became a hermit.
Posts: 591
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
BarryGMC is on a distinguished road
Default Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)

60 degrees? Crap it's barely got above 60 for while. Love it.... New roofs and painting are on right now. Most of my work is done in the shop when it's cold. 50 to 60 is best inside. I can't handle it above 75 and 20 percent humidity. Well we are all different.
Reply With Quote
  #228  
Old October 23rd, 2013, 02:44 AM
tommyduncan tommyduncan is offline
Senior Member
 
Join Date: Jul 2013
Location: Boulder City NV
Truck: 62 3/4ton 305 Hydramatic
Posts: 189
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 117
tommyduncan is on a distinguished road
Default Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)

Just keep chipping away at it. That's how things get finished. Try to bare it long enough to get whole assemblies into the warmth and do what you can.
I just got mine back together finally. It was a chilly 82° here today.

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

Reply With Quote
  #229  
Old November 8th, 2013, 04:30 AM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,779
Thanks: 19
Thanked 4 Times in 3 Posts
Rep Power: 569
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)

Quote:
60 degrees? Crap it's barely got above 60 for while. Love it.... New roofs and painting are on right now. Most of my work is done in the shop when it's cold. 50 to 60 is best inside. I can't handle it above 75 and 20 percent humidity. Well we are all different.
Yup! I know people up north call it garage weather or something like that. They have heaters in the garage and really get alot done. Me, I'm sitting on the heater vent until spring gets here, counting the seconds

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?





Quote:
Just keep chipping away at it. That's how things get finished. Try to bare it long enough to get whole assemblies into the warmth and do what you can.
I just got mine back together finally. It was a chilly 82° here today.

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

82! Man I'd kill for that. It was 64 today but yesterday it was 45!

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?



I started a thread in the "other threads and projects" section on the wood splitter if you guys get bored and need some pictures. Once it's finished I'll try to get the transfer case put together. I'm missin my Cecilia again but I have to get this wood split before it gets super cold.



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?






To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

__________________
Step by steps:

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Some people are like slinkys. Not worth much but funny as heck when pushed down stairs.
__________________
If the women don't find you handsome, they should at least find you handy.
Reply With Quote
  #230  
Old November 21st, 2013, 05:59 PM
BarryGMC BarryGMC is offline
Banned
 
Join Date: Jan 2013
Location: Banned City
Truck: None. Sold them all and became a hermit.
Posts: 591
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
BarryGMC is on a distinguished road
Default Re: 1962 GMC 305V6 4WD Slow DD Build - Cecilia (Pic Heavy)

15 degrees this morning... The welding helmet keeps fogging up. So I am taking a break. I got your info yesterday. Today or tomorrow I will get Cecilia's Christmas present off to you. You know the ladies all like things that sparkle. Barry
Reply With Quote
Reply

Bookmarks

Tags
305 v6, 4 wheel drive, 4x4


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Re: [6066 GMC] So Slow........ Archiver Previous Forum Posts 0 January 29th, 2006 12:53 AM
So Slow........ Archiver Previous Forum Posts 0 January 28th, 2006 12:57 AM
Re: [6066 GMC] So Slow........ Archiver Previous Forum Posts 0 January 28th, 2006 12:29 AM
Re: [6066 GMC] So Slow........ Archiver Previous Forum Posts 0 January 28th, 2006 12:29 AM
slow starts Archiver Previous Forum Posts 0 August 5th, 2002 02:36 PM


All times are GMT +1. The time now is 06:29 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 831730222135|1729056550|0