6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Transmissions and Rear Ends
#Sponsored

Transmissions and Rear Ends Three on the tree or four in the floor? Shift it all here.

Reply
 
Thread Tools
  #1  
Old April 8th, 2021, 01:00 PM
Simonsays Simonsays is offline
Junior Member
 
Join Date: Apr 2021
Location: Los Angeles california
Truck: 1966 3/4 ton
Posts: 20
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 28
Simonsays is on a distinguished road
Default Dana 60 3.23 gears?

Anyone try out doc differential 3.23 gears for Dana 60 rear ends? I've noticed they are the only one I have seen offer it. I have a 66 gmc 1500 with a 4 speed granny tranny being pushed by a chevy 350 short block. Was looking for more hwy cruising speeds. Current gearing can pull a house but it screams past 50. Thanks
Reply With Quote
  #2  
Old April 9th, 2021, 09:31 PM
James James is offline
-= Extreme Supporter =-
 
Join Date: Jun 2013
Location: Greer, SC
Truck: 1964 GMC 1500 2wd
Age: 69
Posts: 449
Thanks: 8
Thanked 4 Times in 3 Posts
Rep Power: 206
James will become famous soon enoughJames will become famous soon enoughJames will become famous soon enough
Default Re: Dana 60 3.23 gears?

I don't think the dana 60 will support a 3.23:1 gear set. I believe a 3.54:1 is the lowest you can go. The 3.54:1 is what I installed in my truck with LTX M/S2 LT235/85R16E tires. On the freeway I believe at 60 mph my rpm is around 2200.

By the way - We normally support GMC V6 engines and not the other brand.
Reply With Quote
  #3  
Old April 10th, 2021, 05:16 PM
Funky61's Avatar
Funky61 Funky61 is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Corona, CA
Truck: 1961 Suburban 1962 GMC Utility
Posts: 1,165
Thanks: 7
Thanked 7 Times in 4 Posts
Rep Power: 421
Funky61 is just really niceFunky61 is just really niceFunky61 is just really niceFunky61 is just really niceFunky61 is just really niceFunky61 is just really nice
Default Re: Dana 60 3.23 gears?

https://www.doctordiff.com/dana-60-ring-and-pinion.html

I guess he was referring to this site that lists them.
__________________
1961 GMC Suburban 305A Overdrive
1962 GMC Utility 305D
Reply With Quote
  #4  
Old April 11th, 2021, 01:54 AM
Simonsays Simonsays is offline
Junior Member
 
Join Date: Apr 2021
Location: Los Angeles california
Truck: 1966 3/4 ton
Posts: 20
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 28
Simonsays is on a distinguished road
Default Re: Dana 60 3.23 gears?

Quote:
Originally Posted by Funky61 View Post
https://www.doctordiff.com/dana-60-ring-and-pinion.html

I guess he was referring to this site that lists them.
Yeah, that's what I ran into in a search. Contacted them and they said it will fit a standard DANA 60 with a 3 series carrier. Also stated it needs I believe a 27 spline pinion yoke. Was just wondering who has tried them if any. Or am I going to be the guinea pig for the site?
Reply With Quote
  #5  
Old September 19th, 2023, 10:15 PM
Simonsays Simonsays is offline
Junior Member
 
Join Date: Apr 2021
Location: Los Angeles california
Truck: 1966 3/4 ton
Posts: 20
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 28
Simonsays is on a distinguished road
Default Re: Dana 60 3.23 gears?

Bump to the top, has anyone tried these yet? They have them back in stock. I don't want to be the guinea pig, I just find it difficult to believe he is the only one to figure out how to get 3.23 gear sets when everyone else can only get 3.54 as the lowest.
Reply With Quote
  #6  
Old September 19th, 2023, 10:57 PM
James James is offline
-= Extreme Supporter =-
 
Join Date: Jun 2013
Location: Greer, SC
Truck: 1964 GMC 1500 2wd
Age: 69
Posts: 449
Thanks: 8
Thanked 4 Times in 3 Posts
Rep Power: 206
James will become famous soon enoughJames will become famous soon enoughJames will become famous soon enough
Default Re: Dana 60 3.23 gears?

That ring gear would have to be very thin to function, in my opinion not possible (not enough room). It more likely for the Dana 70, cause a Dana 70 can go from a 3.07-7.17:1 ratio.
Reply With Quote
  #7  
Old September 20th, 2023, 04:09 AM
Simonsays Simonsays is offline
Junior Member
 
Join Date: Apr 2021
Location: Los Angeles california
Truck: 1966 3/4 ton
Posts: 20
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 28
Simonsays is on a distinguished road
Default Re: Dana 60 3.23 gears?

Quote:
Originally Posted by James View Post
That ring gear would have to be very thin to function, in my opinion not possible (not enough room). It more likely for the Dana 70, cause a Dana 70 can go from a 3.07-7.17:1 ratio.

Not sure, I've been in contact with them and they stated it's just as strong as any other ring and pinion stock. His own personal specs and he has them made to those tolerance. He ran out but just got them back in stock. I just can't find anyone who is running them to get a review.
Reply With Quote
  #8  
Old September 20th, 2023, 01:00 PM
jbgroby's Avatar
jbgroby jbgroby is offline
Senior Member
 
Join Date: Jan 2013
Location: Lacombe, LA.
Truck: 1960 8' fleetside
Posts: 712
Thanks: 0
Thanked 1 Time in 1 Post
Rep Power: 283
jbgroby is a jewel in the roughjbgroby is a jewel in the roughjbgroby is a jewel in the roughjbgroby is a jewel in the rough
Default Re: Dana 60 3.23 gears?

For what it's worth, I have a '60 GMC with a 305V-6 and a DANA 44 rearend; I had the factory 3.92 gears and dropped that down to a 3.23 back in 2012, at the time I had the OEM 4 spd. Hydramatic and no overdrive. The gear change made a WORLD of difference.

Since that swap, the transmission died, and I put in a 700R4 with overdrive. THAT was the ticket, I now turn 80mph at 1800 rpm, the big 305 V-6 LOVES this setup.

Last edited by jbgroby; September 20th, 2023 at 09:12 PM.
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Parting out 305E, SM420, Rockwell Tcase, Dana 44 & Dana 60 Larry 1960-1966 GMC Marketplace 5 October 1st, 2015 05:11 AM
1966 GMC Dana 44 2WD spider gears gmccollector Transmissions and Rear Ends 2 May 14th, 2015 04:28 AM
2.54 gears of similar for Dana 44? phelan Transmissions and Rear Ends 2 June 13th, 2013 09:24 PM
3.07 gears for my Dana 44 phelan Transmissions and Rear Ends 6 April 28th, 2013 02:46 PM
Dana 60 Archiver Previous Forum Posts 0 March 23rd, 2003 12:35 AM


All times are GMT +1. The time now is 06:32 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 771728828974|1727717571|0