6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Transmissions and Rear Ends
#Sponsored

Transmissions and Rear Ends Three on the tree or four in the floor? Shift it all here.

Reply
 
Thread Tools
  #41  
Old April 18th, 2022, 05:24 AM
AZKen's Avatar
AZKen AZKen is offline
Senior Member
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,635
Thanks: 0
Thanked 2 Times in 2 Posts
Rep Power: 524
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Re: 5 speed/o.d. swap comparisons - WC/S10 T5 hybrid, NV4500, A833 MY6, Tremec 3550 Mustang

All this time, money, effort and blogging about transmissions and adapters and you will still have a 3400 RPM motor. The finished product will not do anything a stock GMC won't do except wear out your right arm and left leg. Which will at least cost you your deductible.
If you are after mileage, it will take 10 years to recoup the cost of the mods with fuel savings.

Last edited by AZKen; April 18th, 2022 at 05:32 AM.
Reply With Quote
  #42  
Old April 19th, 2022, 05:13 PM
Prowbar Prowbar is offline
Senior Member
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 433
Thanks: 8
Thanked 9 Times in 8 Posts
Rep Power: 198
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: 5 speed/o.d. swap comparisons - WC/S10 T5 hybrid, NV4500, A833 MY6, Tremec 3550 Mustang

Quote:
Originally Posted by AZKen View Post
All this time, money, effort and blogging about transmissions and adapters and you will still have a 3400 RPM motor. The finished product will not do anything a stock GMC won't do except wear out your right arm and left leg. Which will at least cost you your deductible.
If you are after mileage, it will take 10 years to recoup the cost of the mods with fuel savings.
Maybe, but with a train of thought you mentioned, who would be driving a classic car/truck in the first place? No offense meant.

I do think the V6 will benefit from better gearing compared to say, an SM420. The gears are just too long and the engines do not like to rev.
Reply With Quote
  #43  
Old April 19th, 2022, 08:39 PM
AZKen's Avatar
AZKen AZKen is offline
Senior Member
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,635
Thanks: 0
Thanked 2 Times in 2 Posts
Rep Power: 524
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Re: 5 speed/o.d. swap comparisons - WC/S10 T5 hybrid, NV4500, A833 MY6, Tremec 3550 Mustang

I just don't know what problem people are chasing.
Reply With Quote
  #44  
Old October 28th, 2023, 02:30 AM
Chuck78 Chuck78 is offline
Member
 
Join Date: Jul 2014
Location: Columbus OH
Truck: 1962 GMC 1000 panel truck
Age: 46
Posts: 90
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 86
Chuck78 is on a distinguished road
Default Re: 5 speed/o.d. swap comparisons - WC/S10 T5 hybrid, NV4500, A833 MY6, Tremec 3550 Mustang

Quote:
Originally Posted by AZKen View Post
I just don't know what problem people are chasing.

That's a no-brainer. A wider gear spread for better take off speeds when pulling a light load, and milder highway cruising rpm for better fuel efficiency. Lower RPM on an engine that makes its peak torque at 1600 RPM, basically 1600 to 2200 RPM cruising speeds, will reduce wear on the engine as well, and the engine has plenty of grunt to push the taller overdrive gear. These engines' max horsepower is at 3600 RPM, peak torque at 1600 RPM (352 Magnum at 1400RPM!). dropping 530 RPM at 70mph highway cruising will really help out with fuel economy, and going from a 3spd or current Saginaw 4 speed 1st gear of 3.34:1 up to 3.83:1 will really help with better takeoffs especially when pulling a utility trailer or enclosed trailer with dirtbikes and motorcycles... I don't think I could get better than 17 MPG driving very conservatively on the current worn out Saginaw transmission. I think I can get 21 or 23 MPG with the ax15. Both figures are regarding the 351C engine swap. I have squeeze 21-23mpg out of the 305D. Pulling a utility trailer though (& 640lb Harley FXR), it was a max of maybe 13mpg. I think the 351C will do better mpg when pulling the trailer due to more torque, and lower RPM on the AX-15 as well. I have a transmission with a worn out synchronizer and some slightly worn bearings, so upgrading to a really nice condition $300 AX-15 plus the adapter plate and drive shaft shortening, is a big bonus. This fixes problems on multiple levels.
__________________
Chuck in Ohio
*'62 GMC 1000 Panel Truck - 305D/Saginaw 4sp soon: 351C V6 + AX15 5sp OD trans, & 73-87/91 disc brake front end, rear Cadillac calipers/ AWD Astro rotors, Dana 44 redrilled to 5 lug
*'88 Suzuki Samurai 4x4 project, VW 1.9L mTDI turbodiesel, Toyota V6 LandCruiser drivetrain, full floater axles, future LWB bed stretch
*'77-'79 Suzuki GS motorcycles, '76 Rickman CR900 roadracer.
*Dirtbikes: 2 Kawasaki KDX220R's, '77 Suzuki PE250, '83 PE175
Reply With Quote
  #45  
Old March 28th, 2024, 10:54 PM
krazzz krazzz is offline
Junior Member
 
Join Date: Mar 2023
Location: Ludington, MI
Truck: 1964 1000
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
krazzz is on a distinguished road
Default Re: 5 speed/o.d. swap comparisons - WC/S10 T5 hybrid, NV4500, A833 MY6, Tremec 3550 Mustang

Casey, would you mind if I gave you a call? I'd like to talk through your swap and get an update on how you like it. I will also send you a PM.
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
S10 T5 transmission Archiver Previous Forum Posts 1 December 28th, 2012 04:48 AM
MY6-A833 Tranny info Archiver Previous Forum Posts 14 March 22nd, 2012 02:55 AM
MY6-A833 shift linkage Archiver Previous Forum Posts 3 October 26th, 2011 04:58 AM
Re: BBV6 Flywheels and NV4500/Tremec swaps? Archiver Previous Forum Posts 0 November 13th, 2009 12:02 AM
Re: BBV6 Flywheels and NV4500/Tremec swaps? Archiver Previous Forum Posts 0 November 12th, 2009 12:06 AM


All times are GMT +1. The time now is 10:14 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 781728311253|1727212450|0