6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Transmissions and Rear Ends


Transmissions and Rear Ends Three on the tree or four in the floor? Shift it all here.

Reply
 
Thread Tools
  #1  
Old October 28th, 2023, 03:02 AM
Chuck78 Chuck78 is offline
Member
 
Join Date: Jul 2014
Location: Columbus OH
Truck: 1962 GMC 1000 panel truck
Age: 45
Posts: 90
Rep Power: 82
Chuck78 is on a distinguished road
Default Dana 44 carrier bearings, Detroit TrueTrac swap, axle shaft lengths, spline counts?

I've got a '62 GMC 1000 Panel Truck with the Dana 44 rear end.
I'd like to upgrade to a Detroit TrueTrac or Nitro Helix torsen type limited slip differential when rebuilding the rear end.

I believe from referencing some old posts of mine that perhaps the 60-62 use a 10 spline axle? And 63-67 use a more common 30 spline? I see the old 10 splines are not common, and eventually 19 spline D44 axles were the standard and then 30 spline. I see mention of modern Jeep D44's being 32 spline even.

I know the carrier bearings are a concern with the old Dana 44's found in our trucks. I'm not sure if there is a difference in carrier bearing size between 60-62 and 63-67 or not. So wasn't sure if you could swap an entire carrier from a newer vehicle such as the aftermarkets that I mentioned, into ours with the correct size bearing, and what that bearing size might be.

Is it the carrier bearing o.d. or i.d. that's different, or both? I'd read mention years ago of someone using a more modern Dana 44 rebuild kit but having to machine a spacer to accommodate the different bearing size. So that would tell me that it is just the ID of the bearing that is larger on the newer models, or the OD of the carrier itself that slips into the bearing?

Is there a source for replacement / retro fit Dana 44 30 spline axles for our vehicles? Is there a difference in width or axle shaft lengths between the 60-62 and 63-67?

I've got a 2wd, so switching to a limited slip worm gear type torsen lockup diff will really help when traction is compromised pulling a trailer up steep gravel Forest Service mountain roads or in wet slippery grass. I got stuck with the one legger differential in wet grass once, it was quite embarrassing...
If my gears are worn and don't check out, I may switch from 3.07 to 3.31 ratio, with the intent of swapping an AX-15 overdrive 5 speed into it.

Thanks for the help!
__________________
Chuck in Ohio
*'62 GMC 1000 Panel Truck - 305D/Saginaw 4sp soon: 351C V6 + AX15 5sp OD trans, & 73-87/91 disc brake front end, rear Cadillac calipers/ AWD Astro rotors, Dana 44 redrilled to 5 lug
*'88 Suzuki Samurai 4x4 project, VW 1.9L mTDI turbodiesel, Toyota V6 LandCruiser drivetrain, full floater axles, future LWB bed stretch
*'77-'79 Suzuki GS motorcycles, '76 Rickman CR900 roadracer.
*Dirtbikes: 2 Kawasaki KDX220R's, '77 Suzuki PE250, '83 PE175
Reply With Quote
  #2  
Old October 28th, 2023, 03:13 AM
Chuck78 Chuck78 is offline
Member
 
Join Date: Jul 2014
Location: Columbus OH
Truck: 1962 GMC 1000 panel truck
Age: 45
Posts: 90
Rep Power: 82
Chuck78 is on a distinguished road
Default Re: Dana 44 carrier bearings, Detroit TrueTrac swap, axle shaft lengths, spline counts?

A quick search answered part of the axle spline count question, apparently all 60-68 GMC Dana 44 axles are 30-spline. That makes things a little bit easier now if carrier bearings will be able to be sourced to mate the newer Detroit TrueTrac or Nitro Helix carriers into the older GMC housings...

https://6066gmcclub.com/showthread.p...=Dana+44+axles

Quote:
Originally Posted by summersmoker View Post

The parts manual helps narrow it down. I'm pretty sure the right part # is 2402517 (which according to the gmpartswiki.com became # 02494739).
and:

Quote:
Originally Posted by Charon View Post
1960-68 gmc dana 44 same axles. Not really to hard to find. 61-74 international 1/2 ton works but the flange needs redrilled for 6 bolt pattern and the center hub turned down.
http://tinyurl.com/jptmkjy

Dana-44_1967-1978.pdf which that links takes you to is a Spicer catalog. Page 133 is 1967 plus GMC Dana 44, page 177 is international harvester Dana 44 half ton axles. It shows the part numbers for the GMC axle shafts no longer available, does not give a part number, only in la. But the international axles, it shows part numbers for all of them. They do show a different left versus right shaft however. What I had read here says that the GMC uses the same shaft left and right? I'll have to see if I can find any reproductions to verify that.
The half ton International Dana 44 axles are probably a 5-lug I'm guessing? That would be a bonus for me if any of those were the correct lengths for the '60-'68 GMC. I could run off the shelf International Dana 44 axles and off the shelf 1987 pickup or 1991 Suburban front rotors and have my current 5 lug setup.

That link does have part numbers for the carrier bearings as well, so I can at least look that up at a later date when I get more serious about this, and see what the sizes of those bearings are versus the Detroit TrueTrac OR Nitro Helix 30 spline Dana 44 limited slip.
__________________
Chuck in Ohio
*'62 GMC 1000 Panel Truck - 305D/Saginaw 4sp soon: 351C V6 + AX15 5sp OD trans, & 73-87/91 disc brake front end, rear Cadillac calipers/ AWD Astro rotors, Dana 44 redrilled to 5 lug
*'88 Suzuki Samurai 4x4 project, VW 1.9L mTDI turbodiesel, Toyota V6 LandCruiser drivetrain, full floater axles, future LWB bed stretch
*'77-'79 Suzuki GS motorcycles, '76 Rickman CR900 roadracer.
*Dirtbikes: 2 Kawasaki KDX220R's, '77 Suzuki PE250, '83 PE175

Last edited by Chuck78; October 28th, 2023 at 03:36 AM.
Reply With Quote
  #3  
Old October 28th, 2023, 04:30 AM
Chuck78 Chuck78 is offline
Member
 
Join Date: Jul 2014
Location: Columbus OH
Truck: 1962 GMC 1000 panel truck
Age: 45
Posts: 90
Rep Power: 82
Chuck78 is on a distinguished road
Default Re: Dana 44 carrier bearings, Detroit TrueTrac swap, axle shaft lengths, spline counts?

I've just read of two guys swapping a Detroit TrueTrac into their old GMC housings now, so apparently it's not an issue. I'm going to assume the outside diameter of the bearings is the same, and the inside diameter is all that was the oddball dimension on our original carriers o.d. bearing surface, therefore a modern Dana 44 kit will fit the modern limited slip differentials...



More info:

Quote:
Originally Posted by D-Rat

Re: GMC guys! Dana 44 ??
Most modern D44s are 30 spline, but they did make them in the 60s with like a 19 spline. An International Scout II rear D44 would have 5 on 5.5" lug outers and drum brakes, and may possibly interchange as long as you have 30 spline shafts.

Quote:
Originally Posted by Fitz
Call Currie enterprises. They have axles for your diff in 30, 31, 33, or 35 spline, small or large bearing in a 5 x 5 lug pattern. cost is 319.95 (2010 prices)


Quote:
Originally Posted by fasttech
Get axles turned for a 3" pilot and outer flange diameter of 6.125" or just have some new axles built like I did. When I compared the cost of all the machine work (including 6 to 5 lug) to the cost of new ones it was only about $100 more. Got mine from Dutchman Motorsports.



And here's some great info from several people on rear disc brake swaps:

http://67-72chevytrucks.com/vboard/s...+Dana+44+axles

Apparently a Wilwood kit for Ford 9" works, Wilwood brake set 140-7139, after turning down the drum/wheel register diameter on the end of the shaft to 3" or 3.07" on a lathe. The wheel bearings and the axle tube end flange are the same as the "Big Ford" bolt pattern. I have a set of the OldeDays brackets for the Ford 9" to GM Seville/79-81 Trans Am WS6 calipers, and AWD Astro Van front 5-lug rotors. I believe they are slightly larger diameter than the Cadillac rotors, and the Cadillac rotors would work with those brackets without any bracket mods. I'll mod the brackets to get slightly larger rear rotors. I think it was 11" vs 11.2"?



Quote:
Originally Posted by fasttech
Re: GMC guys! Dana 44 ??
The setup I am using works but I can't comment on the Willwood.

If you want to go the build your own route here is what you need:
* Ford 9" Bracket Kit (from Oldedays)
* Left Rear Caliper GM 79-85 (Cardone 18-4139) this one has the parking brake
* Right Rear Caliper GM 79-85 (Cardone 18-4139) this one has the parking brake
* Brake pads for GM 79-85 rear caliper
* 1978 Seville Rear Rotors (can get get slotted and drilled as option)
* Disc Brake Hose Kit (Gear Head 9828) this one is stainless
* Parking brake cable (BrakeBest BC93292) needs a little customization
* Get axles turned for a 3" pilot and outer flange diameter of 6.125" or just have some new axles built like I did. When I compared the cost of all the machine work (including 6 to 5 lug) to the cost of new ones it was only about $100 more. Got mine from Dutchman Motorsports.
Quote:
Originally Posted by steinepstein
Re: GMC guys! Dana 44 ??
I also just measured the bolt dimensions on the axle housing end. They are the same as a big ford housing end. 3.5" x 2.375". You can find these dimensions on the assembly instructions document on the Wilwood website. Wilwood brake set 140-7139 should bolt right up to that housing end.
I just confirmed that the axle pilot hole will have to be turned down to fit the 140-7139 Wilwood kit, but other than that, the axle housing end and bearing on the Dana 44 is big a Ford 9" setup, awesome.
Quote:
Originally Posted by dougminton
Re: GMC guys! Dana 44 ??
redrill your axles to 5x5 pattern
2 front rotors from a AWD astro van (5x5 pattern) 80$
Rear calipers from 1979 Cadillac Eldorado at rockauto170$ including core
caliper brackets from speedway motors 30$ shipped
longer wheel studs
plus hoses
Quote:
Originally Posted by fasttech
I have researched the crap out of this and starting to collect the required parts for my conversion but here is what I have learned.

The Dana 44 rear ends in the 67-72 trucks have axle mounting flanges based on the Ford 9" early big bearing. So basically any disc brake kit based on the Ford 9" early big bearing will / should work. There are a bunch of disc brake kits out there but the most cost effective approach I could find is to buy the parts individually as follows:

Bracket Kit ($70) - http://shop.oldedaysclassiccarparts....&categoryId=29 You could make your own but I figured it would cost more than $70 in materials and my time to make a set.

1985 Cadillac Seville Calipers ($150 to $200) - eBay is your best bet for a reman set but these are still pricey without a core exchange. Just make sure you get the semi-loaded caliper with all the brackets etc. for the parking brake. I got lucky and found a fresh reman set that a guy needed to get rid of. You could also save a few bucks by using the front calipers off the same car if you don't need and e-brake.

1978 Cadillac Seville Rear Rotors ($60 - $120) - I am going with a 5x5 bolt pattern and these rotors come stock with a 5x5 pattern. You will have to get them re-drilled if you need a different bolt pattern. eBay is probably your best price option here as well. The price will depend on if they are cross drilled, slotted, and with or without pads included.

GM Metric Caliper Brake Hose Kit ($40 - $60) - (2) -3 15" long brake hoses; (2) 3/16" inverted flare to -3 adapters; (2) weld-on brake adapter mounts; (2) brake adapter clips; (2) 10mm x 1.5 banjo bolts; (2) 10mm to -3 banjos; (4) 10mm crush washers. Price depends on if you go with rubber or SS braided hoses.

Axle Modifications - The center pilot hub on this rear end is 3.5" and the pilot hole on the Seville rotors is 3.07" which means you will need to have the hub pilot on both axles turned down to 3". The stock bolt pattern is a 6 lug setup so if you want to change this to some other bolt pattern the axles will have to be re-drilled for that pattern. The wheel studs for the 5x5 pattern is 1/2" so those things like that need to be considered as well. This could end up being a lot of machine work so it may be a better to purchase a set of custom built axles from Dutchman or Moser. I have the axle dimensions if you are interested.

Based on my research you will spend from $450 to $550 plus the axle or rotor mods to convert the rear Dana 44 to disc brakes.
__________________
Chuck in Ohio
*'62 GMC 1000 Panel Truck - 305D/Saginaw 4sp soon: 351C V6 + AX15 5sp OD trans, & 73-87/91 disc brake front end, rear Cadillac calipers/ AWD Astro rotors, Dana 44 redrilled to 5 lug
*'88 Suzuki Samurai 4x4 project, VW 1.9L mTDI turbodiesel, Toyota V6 LandCruiser drivetrain, full floater axles, future LWB bed stretch
*'77-'79 Suzuki GS motorcycles, '76 Rickman CR900 roadracer.
*Dirtbikes: 2 Kawasaki KDX220R's, '77 Suzuki PE250, '83 PE175
Reply With Quote
  #4  
Old October 28th, 2023, 04:34 AM
Chuck78 Chuck78 is offline
Member
 
Join Date: Jul 2014
Location: Columbus OH
Truck: 1962 GMC 1000 panel truck
Age: 45
Posts: 90
Rep Power: 82
Chuck78 is on a distinguished road
Default Re: Dana 44 carrier bearings, Detroit TrueTrac swap, axle shaft lengths, spline counts?

So my only real question now comes down to axle lengths...
Currie, Moser, and Dutchman Motorsports are the recommended places to go for off the shelf or custom axles. I have yet to check any of the reproduction parts catalogs LMC, Brothers, CPP, etc
And I'm wondering if any of the International half ton axles "61-74" will actually interchange? It saud those are a 5 on 5.5" pattern though? And I believe the Chevy truck 1/2 ton two-wheel drive pattern that I am after for a 75 or 76-91 Suburban for 75 or 76-87 pickup is a 5 on 5"? I'll have to go out and measure.
__________________
Chuck in Ohio
*'62 GMC 1000 Panel Truck - 305D/Saginaw 4sp soon: 351C V6 + AX15 5sp OD trans, & 73-87/91 disc brake front end, rear Cadillac calipers/ AWD Astro rotors, Dana 44 redrilled to 5 lug
*'88 Suzuki Samurai 4x4 project, VW 1.9L mTDI turbodiesel, Toyota V6 LandCruiser drivetrain, full floater axles, future LWB bed stretch
*'77-'79 Suzuki GS motorcycles, '76 Rickman CR900 roadracer.
*Dirtbikes: 2 Kawasaki KDX220R's, '77 Suzuki PE250, '83 PE175
Reply With Quote
  #5  
Old October 28th, 2023, 06:18 AM
Chuck78 Chuck78 is offline
Member
 
Join Date: Jul 2014
Location: Columbus OH
Truck: 1962 GMC 1000 panel truck
Age: 45
Posts: 90
Rep Power: 82
Chuck78 is on a distinguished road
Default Re: Dana 44 carrier bearings, Detroit TrueTrac swap, axle shaft lengths, spline counts?

AXLES!!!!
Nitro "cut to length" 30-spline triple drilled Dana 44 axle shafts, 5x4.5, 5x5", & 5x5.5" bolt patterns!
$184!!!!
https://justdifferentials.com/nitro-...r-dana-44.html

https://nitro-gear.com/nitro-gear-ax...1971-2018.html



It says they work for any length from narrow 24.5" Jeep axles up to 32" wide, and I believe ours measure 30.5" according to one comment I read? Please confirm before ordering but I believe ours definitely should fit within this range. Our trucks have fairly narrow wms-wms width axles (wheel mounting surface).

The only thing I'm uncertain on is the center register diameter. This is very easy to turn down in a lathe or make or buy a bushing/adapter for though.

Chromoly 30-spline Dana 44 5 lug on 5" axles for less than $200 each... Wow ��
The only other thing I haven't 100% confirmed is the stock being 30 spline. I read a few mentions of 19 spline, others saying 63-68 were 30 spline, perhaps meaning 60-62 were 19 spline?
If running a Nitro Helix 30 spline limited slip, this makes no difference at all regardless.
Attached Images
File Type: jpg nitro-rear-cut-to-length-axle-shaft-for-dana-44.jpg (132.1 KB, Multiple views, 10 clicks)
__________________
Chuck in Ohio
*'62 GMC 1000 Panel Truck - 305D/Saginaw 4sp soon: 351C V6 + AX15 5sp OD trans, & 73-87/91 disc brake front end, rear Cadillac calipers/ AWD Astro rotors, Dana 44 redrilled to 5 lug
*'88 Suzuki Samurai 4x4 project, VW 1.9L mTDI turbodiesel, Toyota V6 LandCruiser drivetrain, full floater axles, future LWB bed stretch
*'77-'79 Suzuki GS motorcycles, '76 Rickman CR900 roadracer.
*Dirtbikes: 2 Kawasaki KDX220R's, '77 Suzuki PE250, '83 PE175

Last edited by Chuck78; October 28th, 2023 at 06:42 AM.
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Dana 44 carrier bearings jastamjas Transmissions and Rear Ends 2 August 11th, 2020 12:18 AM
64-66 Dana 60 rear axle spline count? GMCNUT Transmissions and Rear Ends 8 May 14th, 2015 04:10 AM
Re: Dana #44 axle Archiver Previous Forum Posts 0 August 1st, 2007 01:53 AM
Re: Dana #44 axle Archiver Previous Forum Posts 0 July 31st, 2007 06:43 AM
Dana 44 spline count Archiver Previous Forum Posts 0 April 10th, 2006 04:41 AM


All times are GMT +1. The time now is 07:06 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 671711554703|1710439616|0