6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > GMC V6 and V12 Engines
#Sponsored

GMC V6 and V12 Engines Engine repair and rebuilding

Reply
 
Thread Tools
  #1  
Old June 16th, 2015, 02:22 AM
AZKen's Avatar
AZKen AZKen is offline
-= Dues Paid =-
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,651
Thanks: 0
Thanked 4 Times in 4 Posts
Rep Power: 529
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Pilot bearing Info Please.

My Pilot bearing fell out when removing trans/clutch. Read on the web it should fit tight. Light to medium press. None of this info was for 305E, but general chevy, ford, etc. They all said to punch/burr up the crank shaft recess that receives the bearing. Or knurl/punch the bearing. This will create a tight fit. I have done this on other parts of trucks and it generally works. My question is: The 305 bearing is in the flywheel not the crank end. I'm getting ready to gouge the recess in the FW. Has anyone done this? and is the 305 bearing supposed to be tight in the flywheel as it is in other installed bearings in other motors? I know it can't escape with the tranny in place and it is not loose in there except axially. Not going to have it knurled or get a new FW. New bearing is 7109.

Last edited by AZKen; June 16th, 2015 at 02:29 AM.
Reply With Quote
  #2  
Old June 16th, 2015, 03:07 AM
bobdylan bobdylan is offline
Senior Member
 
Join Date: Mar 2015
Location: mclouth kansas
Truck: 64 Gmc suburbann 305e, 4speed. v12 truck engine, v12 irrigation,2-305e,305a,305d
Age: 68
Posts: 373
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 156
bobdylan is on a distinguished road
Default Re: Pilot bearing Info Please.

The manual just says to clean the pilot bearing and check for roughness by turning the bearing race. Replace if rough. Thats all it says.
Reply With Quote
  #3  
Old June 16th, 2015, 03:31 AM
AZKen's Avatar
AZKen AZKen is offline
-= Dues Paid =-
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,651
Thanks: 0
Thanked 4 Times in 4 Posts
Rep Power: 529
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Re: Pilot bearing Info Please.

It does need to be lightly tapped to get past the entrance lip which has a "ring ridge" from years of operation. After it's tapped past that and bottoms out on shoulder, it can be pulled back and forth (slides back and forth). I'm all for leaving it that way if others can state if theirs was a press fit or a slip fit. As I say, everything on the internet says pilot bearings are pressed in/tapped in albeit not a 305 V6. Having the OD spin in the hole is not what a bearing should do, if it does that.

Last edited by AZKen; June 16th, 2015 at 03:38 AM.
Reply With Quote
  #4  
Old June 16th, 2015, 03:37 AM
bobdylan bobdylan is offline
Senior Member
 
Join Date: Mar 2015
Location: mclouth kansas
Truck: 64 Gmc suburbann 305e, 4speed. v12 truck engine, v12 irrigation,2-305e,305a,305d
Age: 68
Posts: 373
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 156
bobdylan is on a distinguished road
Default Re: Pilot bearing Info Please.

The manual mentions using a puller to remove the pilot bearing on the straight six only, so I would think that the v6 is not pressed in. But Would like to here what the experts have to say.
Reply With Quote
  #5  
Old June 16th, 2015, 03:41 AM
AZKen's Avatar
AZKen AZKen is offline
-= Dues Paid =-
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,651
Thanks: 0
Thanked 4 Times in 4 Posts
Rep Power: 529
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Re: Pilot bearing Info Please.

Thanks Bob, I did notice that also on my 1960 Manual.
Reply With Quote
  #6  
Old June 17th, 2015, 05:14 AM
AZKen's Avatar
AZKen AZKen is offline
-= Dues Paid =-
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,651
Thanks: 0
Thanked 4 Times in 4 Posts
Rep Power: 529
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Re: Pilot bearing Info Please.

Well I went ahead and chiseled up some burrs on the FW recess and she pressed in tight. Had to hammer pretty hard so I'm satisfied. Put a washer in there first to keep my chisel/burrs out away from the rear shoulder so that burrs would not bunch toward back and keep bearing from seating (bottoming out). Thanks
Reply With Quote
  #7  
Old June 17th, 2015, 05:24 AM
bobdylan bobdylan is offline
Senior Member
 
Join Date: Mar 2015
Location: mclouth kansas
Truck: 64 Gmc suburbann 305e, 4speed. v12 truck engine, v12 irrigation,2-305e,305a,305d
Age: 68
Posts: 373
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 156
bobdylan is on a distinguished road
Default Re: Pilot bearing Info Please.

I'm glad your getting it figured out. I need to but a clutch in my Suburban, and would just as soon learn from you mistakes.
Reply With Quote
  #8  
Old June 17th, 2015, 01:53 PM
Clyde Clyde is offline
Member
 
Join Date: Jan 2013
Location: Abbeville,SC
Truck: 1961 GMC Suburban 4WD-1966 GMC p?u,351,Turbo 400
Age: 82
Posts: 74
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 99
Clyde will become famous soon enough
Default Re: Pilot bearing Info Please.

Green loctite.
__________________
Clyde McKaba
Abbeville,SC
1961 GMC Suburban 4WD 305 V6, 4spd
1966 GMC 3/4T P/U 351 V6, Turbo 400,Gear Vender OD
1969 GMC Suburban 1/2T
Reply With Quote
  #9  
Old June 17th, 2015, 04:58 PM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,789
Thanks: 26
Thanked 7 Times in 6 Posts
Rep Power: 573
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: Pilot bearing Info Please.

The bearing on mine went in the flywheel if I remember right. It just sits in there though. I tried pounding it in the crank hole forever and kept thinking, wow, it wasn't this hard to get out! What's wrong here? I looked at my pics and lo and behold, it didn't go there. Little grease to hold that sucker in and she held right fine till I got the rest of the tranny stabbed through and bolted up.
__________________
Step by steps:

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Some people are like slinkys. Not worth much but funny as heck when pushed down stairs.
__________________
If the women don't find you handsome, they should at least find you handy.
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Clutch pilot bearing Archiver Previous Forum Posts 0 August 21st, 2012 02:14 AM
Re: 401M parts on eBay- pilot bushing / bearing Archiver Previous Forum Posts 0 March 11th, 2010 01:49 AM
pilot bearing Archiver Previous Forum Posts 0 March 11th, 2010 01:19 AM
305 clutch pilot bearing - crankshaft HELP! Archiver Previous Forum Posts 0 March 4th, 2010 06:58 AM
Pilot Bearing Archiver Previous Forum Posts 0 January 15th, 2004 01:38 AM


All times are GMT +1. The time now is 12:17 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 691734197937|1733008634|0