![]() |
![]() |
|
General Discussion Sit down and chat with fellow members! Any topics that don't fit other categories goes here. |
![]() |
|
Thread Tools |
#1
|
|||
|
|||
![]()
how much torque is needed for fuel pump bolts on a gmc 305 v6?
|
#2
|
||||
|
||||
![]()
Strange, No number is given after searching in two manuals.
__________________
1961 GMC Suburban 305A Overdrive 1962 GMC Utility 305D |
#3
|
||||
|
||||
![]()
Funky, use this chart. Use Gr 5. We don't ever need gr 8 on an old truck. You are probably talking 1/4 or 5/16. Anyway, for future, measure the OD of bolt threads, calculate or measure pitch. (fine or coarse) and use the chart. This is a small bolt, it is performing a gasket clamping function in this case. Not holding a bracket, etc. No high torque here. Just snug and a tiny more. Keep hand near where wrench handle meets socket so you can't get much handle leverage. Other cases with small bolts and non gasket, snug plus slow turn to "tight". Torque wrench can be used. As bolt size gets bigger 3/8 7/16 1/2.. use clicker torque wrench. Normally a person can tell by feel that you are getting into the elastic stage....that's a no no. I hardly ever use a torque wrench except on a critical big thread size.. .
Lug nuts, head bolts, pinion nut, axle, steering stuff. You just get a feel after awhile. CLICK The charts do not contemplate a gasket/sealer scenario. Read sealer instructions if used. You are only sealing an oil leak, and mechanical support against cam lever load, not fuel pressure. No big deal. BUT!!! 1/4-20 are the most dangerous bolts we use. Head will snap off. Oil pans and diff covers are in this gasket/small bolt/oil leak category. Water pump needs caution also. Fastener work/restoration needs calipers, thread gauge, taps and dies and torque wrench. SBC specs say 8-11 Ft Lbs for fuel pump. Cast iron thread and gr 5 bolt. Last edited by AZKen; October 1st, 2024 at 05:35 PM. |
The Following User Says Thank You to AZKen For This Useful Post: | ||
Funky61 (October 1st, 2024) |
#4
|
||||
|
||||
![]()
Very sorry Funky....I addressed the wrong person. I should have said Big Red....not you. You were providing help and I skipped a beat when reading the posts.
![]() The advice/suggestions apply to BigRed Last edited by AZKen; October 4th, 2024 at 08:44 AM. |
#5
|
|||
|
|||
![]()
snug
__________________
Jerr 1963 305 V6 1500 To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. |
![]() |
Bookmarks |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Intake Manifold Torque spec | makindust | GMC V6 and V12 Engines | 7 | December 5th, 2015 05:08 AM |
Need Torque Spec for 305 heads | wcstory | GMC V6 and V12 Engines | 6 | July 7th, 2015 09:39 PM |
torque spec. | Archiver | Previous Forum Posts | 0 | March 6th, 2004 01:58 PM |
Re: [6066 GMC Truck] torque spec. | Archiver | Previous Forum Posts | 0 | March 6th, 2004 12:17 AM |
Re: torque spec. | Archiver | Previous Forum Posts | 0 | March 6th, 2004 12:04 AM |