6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Transmissions and Rear Ends


Transmissions and Rear Ends Three on the tree or four in the floor? Shift it all here.

Reply
 
Thread Tools
  #31  
Old October 3rd, 2021, 01:29 AM
Jim A Jim A is offline
Member
 
Join Date: Jan 2013
Location: Potter Valley, CA
Truck: 1960 3/4, 4 spd, stepside
Posts: 62
Rep Power: 70
Jim A is on a distinguished road
Default Re: Problem with clutch disengaging

Just talking to myself here.
Even though the throw-out bearing turns freely and quietly under testing (standing on it and spinning), the only thing that could have caused the release fingers and the big lever to have worn where they did as a much as they did was if the bearing froze for an extended time.
If I can find three new fingers and a correct t/o bearing, I will have hope for a fix.
Reply With Quote
  #32  
Old October 3rd, 2021, 02:21 AM
Funky61's Avatar
Funky61 Funky61 is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Corona, CA
Truck: 1961 Suburban 1962 GMC Utility
Posts: 1,006
Rep Power: 339
Funky61 is a jewel in the roughFunky61 is a jewel in the roughFunky61 is a jewel in the roughFunky61 is a jewel in the rough
Default Re: Problem with clutch disengaging

Jim, have checked this page for part numbers

http://6066gmcguy.com/partnumbers.html

or even PM Lewis Matkin as he’s the parts number Guru
__________________
1961 GMC Suburban 305A Overdrive
1962 GMC Utility 305D
Reply With Quote
  #33  
Old October 15th, 2021, 05:44 PM
Jim A Jim A is offline
Member
 
Join Date: Jan 2013
Location: Potter Valley, CA
Truck: 1960 3/4, 4 spd, stepside
Posts: 62
Rep Power: 70
Jim A is on a distinguished road
Default Re: Problem with clutch disengaging

I am having no luck finding the three release levers (fingers) that I think will put my '60 1500 back on the road and pasture.
They carry the number C-4B-200-F; the B could be an 8.
They have two holes for pivots at .475 diameter, with a weird plug in the outer one.
I am hoping someone has a pile of (or even one) pressure plates with good levers.
I don't need the plate and the levers would be easier to ship.
Thanks
Reply With Quote
  #34  
Old October 15th, 2021, 07:12 PM
Funky61's Avatar
Funky61 Funky61 is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Corona, CA
Truck: 1961 Suburban 1962 GMC Utility
Posts: 1,006
Rep Power: 339
Funky61 is a jewel in the roughFunky61 is a jewel in the roughFunky61 is a jewel in the roughFunky61 is a jewel in the rough
Default Re: Problem with clutch disengaging

Is this the part with the fingers you are looking for?

https://www.ebay.com/itm/11504617354...EAAOSwwMZhXywc
__________________
1961 GMC Suburban 305A Overdrive
1962 GMC Utility 305D
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
HEI Problem Archiver Previous Forum Posts 0 March 27th, 2008 01:49 AM
6066gmc 60 model clutch problem Archiver Previous Forum Posts 0 July 4th, 2006 01:25 AM
run-on problem Archiver Previous Forum Posts 0 February 4th, 2006 12:32 AM
Re: have a problem Archiver Previous Forum Posts 0 December 4th, 2003 12:48 AM
have a problem Archiver Previous Forum Posts 0 December 3rd, 2003 12:08 AM


All times are GMT +1. The time now is 03:34 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 821634778630|1633746868|0
Feedback Buttons provided by Advanced Post Thanks / Like (Lite) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.