6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > GMC V6 and V12 Engines
#Sponsored

GMC V6 and V12 Engines Engine repair and rebuilding

Reply
 
Thread Tools
  #1  
Old January 2nd, 2022, 01:33 AM
mcmyket mcmyket is offline
Junior Member
 
Join Date: Dec 2021
Location: Washington, DC
Truck: 1964 GMC C10
Age: 51
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
mcmyket is on a distinguished road
Default Holley Sniper 2300

Hello,

I have a 64 GMC with a 305 v6 that I've recently purchased and was considering a Holley Sniper 2300 fuel injection setup for it. I see there was a thread in 2020 talking about it, but I don't see where anyone has completed an installation. Has this setup or any other fuel injection system worked for anyone yet.

Thanks!

Mike
Attached Images
File Type: jpg idaho c102.jpg (195.3 KB, Multiple views, 12 clicks)
Reply With Quote
  #2  
Old March 8th, 2022, 03:49 PM
Gwhizzard Gwhizzard is offline
Member
 
Join Date: Jun 2020
Location: Friendsville Tennessee
Truck: 1963 GMC c2500
Age: 34
Posts: 32
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 38
Gwhizzard is on a distinguished road
Default Re: Holley Sniper 2300

the only thing that doesn't help and might throw it off is the intake being it does not really distribute fuel equally. but have seen post on the 67-72 forum that showed a 61 suburban with 88 gm tbi unit on it. so id say go for it and see what happens lol ive looked into it as well. but haven't pulled trigger et on anything due to other projects inline first.
Reply With Quote
  #3  
Old March 8th, 2022, 04:56 PM
Prowbar Prowbar is offline
Senior Member
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 436
Thanks: 8
Thanked 10 Times in 9 Posts
Rep Power: 199
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: Holley Sniper 2300

Quote:
Originally Posted by Gwhizzard View Post
the only thing that doesn't help and might throw it off is the intake being it does not really distribute fuel equally.
How do you know it doesn't distribute the air-fuel mixture properly?

@Mike: I for one, don't know anyone that has one of these V6's on (Holley) EFI, except for the Chevy TBI system. I'd be very interested though if you decide to try!
But I believe that port injection is superior to these TBI units though.

Last edited by Prowbar; March 8th, 2022 at 05:06 PM.
Reply With Quote
  #4  
Old March 9th, 2022, 01:58 PM
James James is online now
-= Extreme Supporter =-
 
Join Date: Jun 2013
Location: Greer, SC
Truck: 1964 GMC 1500 2wd
Age: 69
Posts: 450
Thanks: 10
Thanked 4 Times in 3 Posts
Rep Power: 207
James will become famous soon enoughJames will become famous soon enoughJames will become famous soon enough
Default Re: Holley Sniper 2300

Quote:
Originally Posted by Prowbar View Post
How do you know it doesn't distribute the air-fuel mixture properly?

@Mike: I for one, don't know anyone that has one of these V6's on (Holley) EFI, except for the Chevy TBI system. I'd be very interested though if you decide to try!
But I believe that port injection is superior to these TBI units though.
I have flow tested the intake manifold and found with the stock two barrel carburetor the flow is about equal. With the Holley two barrel the center runner flow is very low. This is why the magnum intake has no divider between runner 1-3 and 4-6. If you look at the top of the manifold you will see the center runner makes a 90° turn, air don't like to make sharp turn so it restrict the air flow.

In my opinion, port injection is superior but with these engines a TBI would be better base on the intake limitation.

Last edited by James; March 9th, 2022 at 02:28 PM.
Reply With Quote
  #5  
Old March 9th, 2022, 05:09 PM
Gwhizzard Gwhizzard is offline
Member
 
Join Date: Jun 2020
Location: Friendsville Tennessee
Truck: 1963 GMC c2500
Age: 34
Posts: 32
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 38
Gwhizzard is on a distinguished road
Default Re: Holley Sniper 2300

Prowbar.. I personally have not flow tested or tried to improve the intake yet... but i have read alot of the 4 barrel carb mods and the one thing they do is soften the turns up inside of the intake to make it smoother transition. There are a few on 67-72 and jalopy journal of people modding these intakes. if they are still out there.
Reply With Quote
  #6  
Old March 9th, 2022, 05:37 PM
James James is online now
-= Extreme Supporter =-
 
Join Date: Jun 2013
Location: Greer, SC
Truck: 1964 GMC 1500 2wd
Age: 69
Posts: 450
Thanks: 10
Thanked 4 Times in 3 Posts
Rep Power: 207
James will become famous soon enoughJames will become famous soon enoughJames will become famous soon enough
Default Re: Holley Sniper 2300

Quote:
Originally Posted by Gwhizzard View Post
Prowbar.. I personally have not flow tested or tried to improve the intake yet... but i have read alot of the 4 barrel carb mods and the one thing they do is soften the turns up inside of the intake to make it smoother transition. There are a few on 67-72 and jalopy journal of people modding these intakes. if they are still out there.
This is what I had done to my intake ports and the carb flange on the intake manifold:

On the carb flange picture, I was almost done, just wanted to show how much metal was removed.

On the ports, I left a small section of the runner divider to hold the gasket in place and so I would be able to install any small port heads without issue. Did not make the port any larger, just remove the divider.

This manifold now flow very well with the Holley 2 barrels.

It took a lot of work and patient to get it there. Engine run better too. Want to pull harder.
Attached Images
File Type: jpg Carb flang mods in progress.jpg (4.81 MB, Multiple views, 21 clicks)
File Type: jpg Intake ports with most of runner divider removed.jpg (4.39 MB, Multiple views, 19 clicks)
File Type: jpg Flow testing manifold with carb.jpg (4.32 MB, Multiple views, 19 clicks)
Reply With Quote
  #7  
Old March 10th, 2022, 10:41 AM
Prowbar Prowbar is offline
Senior Member
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 436
Thanks: 8
Thanked 10 Times in 9 Posts
Rep Power: 199
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: Holley Sniper 2300

Looks excellent. Regarding the Holley conversion, this is something that one needs to pay attention to.

Quite surprised the intake does distribute the flow equally. However, with the sonic pulses that might be different. The only way to test that would be to make a spacer plate that mounts between the cylinder head and exhaust manifold and has 3 O2 sensors, connected to each runner, to measure the A/F ratio of each cylinder.

Another point regarding the A/F ratio of each cyl. would be the PCV valves tapping into runners 3 and 5 but not in runner 1. This should affect the A/F of 3 and 5 to some degree. Especially with a worn engine.

A centralized PCV would be better I think.
Reply With Quote
  #8  
Old March 10th, 2022, 12:51 PM
Gwhizzard Gwhizzard is offline
Member
 
Join Date: Jun 2020
Location: Friendsville Tennessee
Truck: 1963 GMC c2500
Age: 34
Posts: 32
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 38
Gwhizzard is on a distinguished road
Default Re: Holley Sniper 2300

Nice setup. I like what you did with it..
Reply With Quote
  #9  
Old March 10th, 2022, 01:52 PM
James James is online now
-= Extreme Supporter =-
 
Join Date: Jun 2013
Location: Greer, SC
Truck: 1964 GMC 1500 2wd
Age: 69
Posts: 450
Thanks: 10
Thanked 4 Times in 3 Posts
Rep Power: 207
James will become famous soon enoughJames will become famous soon enoughJames will become famous soon enough
Default Re: Holley Sniper 2300

Quote:
Originally Posted by Prowbar View Post
Another point regarding the A/F ratio of each cyl. would be the PCV valves tapping into runners 3 and 5 but not in runner 1. This should affect the A/F of 3 and 5 to some degree. Especially with a worn engine.

A centralized PCV would be better I think.
The PCV valves will lean out cylinder 1-3 and 4-6. It also effect the flow through the runners, base on my flow bench numbers. Blocking the passage between the ports will change the flow rate. When I get done with modifying my spare heads, it will not have the internal PCV valves only an external one.
Reply With Quote
  #10  
Old March 10th, 2022, 04:22 PM
Prowbar Prowbar is offline
Senior Member
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 436
Thanks: 8
Thanked 10 Times in 9 Posts
Rep Power: 199
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: Holley Sniper 2300

You're correct regarding the ports. I'm still thinking about the PCV system conversion. On my IMPCO propane mixer air cleaner, I have a way to attach a PCV hose. Now to tap into the engine. Either convert the filter canister on the back of the block or use one of the valve covers. I don't like drilling holes in original parts, possibly a custom oil fill cap with a PCV hose fitting in the center.

What are your thoughts?
Reply With Quote
Reply

Bookmarks

Tags
efi, electronic fuel injection, fuel injection


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
2300 Holley 4412 Archiver Previous Forum Posts 0 December 25th, 2004 03:20 AM
Re: [6066 GMC] Holley 2300, beware! Archiver Previous Forum Posts 0 September 28th, 2004 04:35 AM
Re: [6066 GMC] Holley 2300, beware! Archiver Previous Forum Posts 0 September 27th, 2004 04:09 AM
Holley 2300, beware! Archiver Previous Forum Posts 0 September 26th, 2004 02:47 PM
Holley 2300 adapter Archiver Previous Forum Posts 0 May 3rd, 2004 01:17 AM


All times are GMT +1. The time now is 12:16 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 841730414881|1729206996|0