6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > GMC V6 and V12 Engines
#Sponsored

GMC V6 and V12 Engines Engine repair and rebuilding

Reply
 
Thread Tools
  #1  
Old May 7th, 2023, 06:44 PM
Mulana Mulana is offline
-= Dues Paid =-
 
Join Date: Aug 2020
Location: Monroe, Oregon
Truck: I don't own one - YET!
Age: 60
Posts: 44
Thanks: 0
Thanked 2 Times in 1 Post
Rep Power: 41
Mulana is on a distinguished road
Default Block to Oil Filter Housing Routing?

It's a beautiful, sunny day in Oregon!
Question: I am putting my 432 back together, and I thought I would remember how the oil lines from the block to the oil filter housing went, but after three years in the machinist shop, I do not. The block uses an oil pump type governor, but I will not be using the governor type carburetor. There are two through-block fittings, three 1/8" NPT threaded holes on top of the filter housing, and two very large fittings for the oil cooler. I vaguely remember one of the three fittings on top of the housing is plugged. Please help me figure this out. If I did the post correctly, there should be a photo of the assembly below (or somewhere).

Thanks, Jim.
Attached Files
File Type: pdf OIL LINE ROUTE.pdf (40.0 KB, Multiple views, 19 clicks)
Reply With Quote
  #2  
Old May 7th, 2023, 09:23 PM
Funky61's Avatar
Funky61 Funky61 is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Corona, CA
Truck: 1961 Suburban 1962 GMC Utility
Posts: 1,167
Thanks: 11
Thanked 8 Times in 5 Posts
Rep Power: 421
Funky61 is just really niceFunky61 is just really niceFunky61 is just really niceFunky61 is just really niceFunky61 is just really niceFunky61 is just really nice
Default Re: Block to Oil Filter Housing Routing?

I have this old photo from a 401M and its all I have. I also looked through some manuals and could not find any diagrams. Hope it jars more bits of memory.
Attached Images
File Type: jpg Canister Oil routing.JPG (246.9 KB, Multiple views, 19 clicks)
__________________
1961 GMC Suburban 305A Overdrive
1962 GMC Utility 305D
Reply With Quote
  #3  
Old May 8th, 2023, 07:00 AM
Mulana Mulana is offline
-= Dues Paid =-
 
Join Date: Aug 2020
Location: Monroe, Oregon
Truck: I don't own one - YET!
Age: 60
Posts: 44
Thanks: 0
Thanked 2 Times in 1 Post
Rep Power: 41
Mulana is on a distinguished road
Default Re: Block to Oil Filter Housing Routing?

Funky61: Thanks for your quick reply. I do see a couple of plugs on one side. I think it's a different filter housing since it does not have the large fittings for the oil cooler. I wish I had taken a photo or made a drawing of my setup before disassembly. Oh, well.
Reply With Quote
  #4  
Old May 8th, 2023, 03:00 PM
Prowbar Prowbar is offline
Senior Member
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 444
Thanks: 9
Thanked 11 Times in 10 Posts
Rep Power: 201
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: Block to Oil Filter Housing Routing?

On my '62 478, one of the block ports (utmost rear) is used for the governor line. The other port is blocked off with a plug.
No oil cooler or other ports are present on the oil filter. I switched to the spin-on type, which only has an oil pressure sender port.

Are you planning to run an oil cooler?
Reply With Quote
  #5  
Old May 9th, 2023, 04:51 AM
Mulana Mulana is offline
-= Dues Paid =-
 
Join Date: Aug 2020
Location: Monroe, Oregon
Truck: I don't own one - YET!
Age: 60
Posts: 44
Thanks: 0
Thanked 2 Times in 1 Post
Rep Power: 41
Mulana is on a distinguished road
Default Re: Block to Oil Filter Housing Routing?

I figure I might as well, but the lines are really large... I don't know if I will be able find a cooler with big enough lines. Based upon what you are saying, I could probably plug off both hardline ports at the governor if I am using a regular carburetor. If one of the block ports is for the governor line, what is the other one for... a psi gauge?

Thanks for your reply.
Reply With Quote
  #6  
Old May 9th, 2023, 09:15 AM
Prowbar Prowbar is offline
Senior Member
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 444
Thanks: 9
Thanked 11 Times in 10 Posts
Rep Power: 201
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: Block to Oil Filter Housing Routing?

Here's what I think the ports are for. On my 478 I believe they fed the air compressor from the 1/8 NPT port before the right cylinder bank, but I bought the engine in parts. I think the rear ports are for accessory purposes.

Don't think an oil cooler would be needed in a pickup with such a big engine.
Attached Images
File Type: png Oil filter routing.png (386.1 KB, Multiple views, 5 clicks)
Reply With Quote
  #7  
Old May 10th, 2023, 07:12 AM
Mulana Mulana is offline
-= Dues Paid =-
 
Join Date: Aug 2020
Location: Monroe, Oregon
Truck: I don't own one - YET!
Age: 60
Posts: 44
Thanks: 0
Thanked 2 Times in 1 Post
Rep Power: 41
Mulana is on a distinguished road
Default Re: Block to Oil Filter Housing Routing?

Yes, that makes sense. The timing cover has provisions for a large air compressor unit.
I don't need the oil cooler, but it could be "cool".
Thanks for your help, I appreciate it a bunch.
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
oil filter housing , Archiver Previous Forum Posts 8 May 6th, 2012 11:21 AM
Oil Filter Housing Archiver Previous Forum Posts 0 August 11th, 2009 02:40 AM
Oil filter Housing Archiver Previous Forum Posts 0 August 10th, 2009 02:04 AM
Re: [6066 GMC Truck] oil filter housing & crank vent housing needed Archiver Previous Forum Posts 0 December 8th, 2002 08:37 AM
oil filter housing & crank vent housing needed Archiver Previous Forum Posts 0 December 6th, 2002 01:52 AM


All times are GMT +1. The time now is 12:55 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 921731597221|1730505320|0