Pay Dues or become a Site Supporter |
|
General Discussion Sit down and chat with fellow members! Any topics that don't fit other categories goes here. |
|
Thread Tools |
#21
|
||||
|
||||
Re: What did you do for your GMC today?
i drove the 66 to adair ia. for pizza sat night. zips pizza, best pizza in iowa. it's about 25 miles, but we took the long way, put on about 75 miles. nice to have the wind blowing in the windows, who needs a radio.
|
#22
|
||||
|
||||
Re: What did you do for your GMC today?
__________________
Step by steps: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Some people are like slinkys. Not worth much but funny as heck when pushed down stairs. __________________ If the women don't find you handsome, they should at least find you handy. |
#23
|
|||
|
|||
Re: What did you do for your GMC today?
Quote:
When I straight piped my 7.3L PSD in my F-250, it whistled so nice from the turbo I'd run with the passenger side window open about 3 inches even in below zero weather. The heater in the newer Ford's were good enough to keep your warm. Drove 70 miles home from work one Friday night with a shattered driver's door window. Had an inch or two of snow, stuck the weather stripping to the glass. Hit the power window down button and the window shattered like it was shot with a 30-06! |
#24
|
||||
|
||||
Re: What did you do for your GMC today?
On my 62 I pulled the motor back out completely disassembled it and took the bare block,crank,rods and pistons,front hub and flywheel to my machine shop. Dave
|
#25
|
||||
|
||||
Re: What did you do for your GMC today?
I open the hood. And then I said I do good work, when I do it.
|
#26
|
||||
|
||||
Re: What did you do for your GMC today?
I opened the hood too, but just disconnected the battery tender and turned her over to make sure she still wanted to start. No problem!
I'm still tied up to other projects, but soon she'll get her transmission pulled and I'll try to figure out why the heck 2nd gear isn't working.
__________________
Step by steps: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Some people are like slinkys. Not worth much but funny as heck when pushed down stairs. __________________ If the women don't find you handsome, they should at least find you handy. |
#27
|
|||
|
|||
Re: What did you do for your GMC today?
got stuck.. and ordered a 500 cfm holley
|
#28
|
||||
|
||||
What I did for my truck today
Hi all,
I've seen this on other forums as a way to help inspire/motivate each other to keep "betterin" our rigs. Maybe it'll catch on here, maybe not but in any case I'll start off. Today I installed a new door stopper for the driver's door. The original one was broke and the door was being stopped by the upper fender/cowl piece if one wasn't careful (of course I was...but that p.o!) and it has dented the door. To replace the stopper I had to take out the vent wing window and the window and mechanism. It seemed a lot of effort for something that is just 2 screws but now I know how to do it when the time comes to replace all those worn out seals and felts! It is sure nice not to have to worrying about further damage on the door. |
#29
|
|||
|
|||
Re: What I did for my truck today
Hello back, I have seen this thread on other forums and it is one of the largest and longest running too. Great idea on your part. I finished up a restoration on my 53 Chev 3100 in 2018 and my entire premise was to get out in the garage everyday for at least 1/2 hour. Even if you only go out there to look around and think, it was a great opportunity to keep things going if not to make lists for future ordering of parts and supplies. Stalled restoration projects are caused because for lack of a better term recent familiarity. In other words, you forgot what you were doing, or what you needed to buy to keep it going or where you put something. Threads like this keep the interest and tends to keep people moving towards completion.
So with that said, I removed the left front tire and wheel of my 64 GMC and bird-dogged the slow leak to a leaky valve stem. Took it up to the tire store and had them dismount and replace the stem, and get this a big bonus-- it cost me nothing. BTW, I'm just up the street from you, what are you working on? Lets keep this going. Steve
__________________
Steve Stock Gig Harbor, Wa 1953 Chevrolet 3100 261 cu inch, SM420 Finished Cab off restoration 1964 GMC 1000 305 V6, SM 420 Restoration is now started, still looking for an oldsmobile style power steering pump |
#30
|
|||
|
|||
Re: What did you do for your GMC today?
Threads merged.
|
Bookmarks |
Thread Tools | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Re: What I did today. | Archiver | Previous Forum Posts | 0 | February 15th, 2005 07:45 AM |
What I did today. | Archiver | Previous Forum Posts | 0 | February 5th, 2005 07:19 AM |
Re: Here is what I got today. | Archiver | Previous Forum Posts | 0 | March 29th, 2004 01:44 AM |
Here is what I got today. | Archiver | Previous Forum Posts | 0 | March 23rd, 2004 07:56 AM |
Re: Here is what I got today. | Archiver | Previous Forum Posts | 0 | March 23rd, 2004 01:23 AM |