Pay Dues or become a Site Supporter |
|
Wheels, Tires, Suspension and Brakes Keep them doggies rollin', rawhide |
|
Thread Tools |
#1
|
|||
|
|||
Bolt pattern for 1963 8 hole 8x17.5
First post, in the process of purchasing a truck. Need to get it running and then to the tires and or wheels.
Getting it running should not be an issue. Tires on it now are 8-17.5. Not that they are unobtanium, just in my area. It has solid rims, that is a plus as no one will work on lock ring or split rims in this area. I am trying to figure out the center diameter and bolt circle diameter for a 1963 2500 medium duty small grain truck. I would like to see if 16 inch wheels will clear everything on both front and rear. Any help is appreciated. Last edited by Scrapcan; April 4th, 2022 at 04:51 AM. |
#2
|
||||
|
||||
Re: Bolt pattern for 1963 8 hole 8x17.5
Quote:
__________________
Step by steps: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Some people are like slinkys. Not worth much but funny as heck when pushed down stairs. __________________ If the women don't find you handsome, they should at least find you handy. |
#3
|
|||
|
|||
Re: Bolt pattern for 1963 8 hole 8x17.5
We have agreed to buy it pending running condition and enough tires to be able to move it out of the building it is stored in. It has been setting fir 10 years or more. Out of the weather but dirt floor, tires are shot.
|
#4
|
|||
|
|||
Re: Bolt pattern for 1963 8 hole 8x17.5
i have 63 gmc 2503 8 lug dually.. i used square body dually wheels and tires for mine i had some left over but you have to use tapered lug nuts and or drill and press in bigger studs bc the stud sizes are 1/16 different between each other. But i bought half inch tapered lug nuts and it tightened right up and driving around fine so far. Some people will argue that you have to put bigger studs on it but from what i noticed that is not the case...
|
#5
|
|||
|
|||
Re: Bolt pattern for 1963 8 hole 8x17.5
Appears to be a very nice original truck!
|
#6
|
|||
|
|||
Re: Bolt pattern for 1963 8 hole 8x17.5
@ Gwhizzard
You did not have clearance issues anywhere with 16 inch wheels did you? I appreciate the help. I have scoured the recesses looking for info and was headed to the salvage yard tomorrow to see if I could find 2 to try. Gives me hope! |
#7
|
|||
|
|||
Re: Bolt pattern for 1963 8 hole 8x17.5
@ snazzypig
It isn’t too bad a few things need attention, like they took the seat out and built a wooden deck with cushions. More to come when We get it rolling under it’s own power Last edited by Scrapcan; April 8th, 2022 at 12:57 AM. |
#8
|
|||
|
|||
Re: Bolt pattern for 1963 8 hole 8x17.5
Nope Not at all i put all new brake components on it except for the drums bc they are hard to find. But they bolted up and no clearance issues. but i run a little smaller tire size on the front then the rears. ill try to post picture up of mine so you can see it... Your truck looks good though hope you save her.
|
#9
|
|||
|
|||
Re: Bolt pattern for 1963 8 hole 8x17.5
https://6066gmcclub.com/showthread.php?t=50872
This thread ahs my truck in it and last page shows her sitting with the tires on her |
Bookmarks |
Thread Tools | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Bolt pattern and lug nut size? | Rustbucket | Wheels, Tires, Suspension and Brakes | 3 | May 17th, 2014 05:36 PM |
BOLT PATTERN | Archiver | Previous Forum Posts | 0 | August 29th, 2004 02:46 AM |
Re: [6066 GMC] BOLT PATTERN | Archiver | Previous Forum Posts | 0 | August 29th, 2004 02:25 AM |
Bellhousing bolt pattern | Archiver | Previous Forum Posts | 0 | December 16th, 2001 07:03 AM |
Re: [6066 GMC Truck] Bellhousing bolt pattern | Archiver | Previous Forum Posts | 0 | December 16th, 2001 06:42 AM |