6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Wheels, Tires, Suspension and Brakes
#Sponsored

Wheels, Tires, Suspension and Brakes Keep them doggies rollin', rawhide

Reply
 
Thread Tools
  #11  
Old March 4th, 2016, 01:59 AM
AZKen's Avatar
AZKen AZKen is offline
-= Dues Paid =-
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,647
Thanks: 0
Thanked 3 Times in 3 Posts
Rep Power: 527
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Re: Need 4x4 front brake hose Part Number

Two green rears are Pre flared lines (I bent) from O'reillys, all the rest is bulk tubing I fabbed. (copied most of the old lines). Gotta do the fuel line next, then the UJoints (6), drop motor in to test Xfer/trans etc. Was a semi basket case when I got it so never run/driven. Then on to the body and wire and ...... restore some plaid covers among many other things.
So far, besides the plumbing and issues, rebuilt entire rear D44 differential.and wheel brgs. Rebuilt the front hubs with trunion brgs, wheel brgs, knuckle seals. Shoes, cylinders, springs, hoses, seals and brake hardware all around. Painting the frame as I clean and degrease. Fabbed upper front shock mounts, finding parts, refurbished/serviced motor (305D, 305A was toast) and trans and painted both. Rebuilt carb and starter and breather. New pumps and Ignition parts. New clutch, brgs, master cylinder and slave. In between all the honey-do's and honey-don't's. Thanks to everyone here and Barry for help.

Last edited by AZKen; March 4th, 2016 at 02:19 AM.
Reply With Quote
  #12  
Old August 21st, 2023, 02:51 PM
Ledslinger Ledslinger is offline
Member
 
Join Date: Nov 2022
Location: Lake Lotawana, Missouri
Truck: 1961 K1001 Suburban
Posts: 53
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 27
Ledslinger is on a distinguished road
Default Re: Need 4x4 front brake hose Part Number

I searched far and wide for the correct wheel cylinder adapter for my 1962 GMC K1000 Suburban. Never found any, but I did find a solution and a quick easy way to make them from an existing and available fitting. This is two threads about it I posted on the 47-66 Chevy truck forum.

I went to Tompkins Industries, a hydraulic hose supplier today, and showed them a sample 1962 GMC K1000 front brake hose fitting and they said they had 729 of them at their Olathe store. I drove across Kansas City to get them and thought I was in luck, but the male part of the fitting was 1/8" NPT pipe thread instead of straight 3/8"-24. The counter guy looked through all types of catalogs to find one, and was looking at ways to use two fittings to adapt it. I didn't want two fittings.

I bought two of the fittings with the male 1/8" NPT and was thinking I'd drill and tap the male end and thread in a section of a 3/8"-24 bolt and silver solder it in. Then I figured out if I removed the threads on the fitting, it would still be thicker than the major diameter of 3/8"-24 threads: .3667. So I will file off the threads on the male portion while spinning in a drill press, and try to run a die down it. I don't have a lathe.

The fitting part number is 6404-04-02. It has correct 7/16"-20 threads on the female end.

My plan to file down the 1/8" NPT steel fitting down to .3667, and thread to 7/16"-20 worked perfect. I cut the head off a 7/16"-20 bolt to screw into the fitting and chucked the non threaded bolt shank into the drill chuck. Laid my small drill press on its side to do the filing, then stood it up and spun it by hand in the die and stock laid on the drill press table.

Some have solved the problem by tapping the wheel cylinder to 7/16"-20 and using no adapter, but I wanted to keep the original setup with the adapter. Nobody cares about this unless you still have drum brakes on a 1960-1963 or so GMC K1000 or K10, but I have seen several discussions in the past seeking this fitting.
Reply With Quote
  #13  
Old August 24th, 2023, 02:28 PM
Ledslinger Ledslinger is offline
Member
 
Join Date: Nov 2022
Location: Lake Lotawana, Missouri
Truck: 1961 K1001 Suburban
Posts: 53
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 27
Ledslinger is on a distinguished road
Default Re: Need 4x4 front brake hose Part Number

I made an error in my previous post: "My plan to file down the 1/8" NPT steel fitting down to .3667, and thread to 7/16"-20 worked perfect." I should have said: and thread to 3/8"-24.
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Genral Motors brake part number/ picture needed Wizard2467 Wheels, Tires, Suspension and Brakes 0 June 20th, 2013 11:49 PM
Good Part Number for Brake Light Switch Archiver Previous Forum Posts 6 March 16th, 2011 02:40 AM
Re: front engine mount part number Archiver Previous Forum Posts 0 June 1st, 2007 04:14 AM
front engine mount part number Archiver Previous Forum Posts 0 May 31st, 2007 02:53 AM
Re: [6066 GMC] front engine mount part number Archiver Previous Forum Posts 0 May 31st, 2007 02:53 AM


All times are GMT +1. The time now is 10:13 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 911731597221|1730409180|0