Pay Dues or become a Site Supporter |
|
Interiors, Dash, Lights and Electrical Everything Inside |
|
Thread Tools |
#1
|
|||
|
|||
66 GMC Heater control/switch not working
I have a three slider heater control/switch in my 66 GMC that is not working. The middle lever is an air/fan "Off-Lo-Med-Hi" switch. The left lever is DEFROST, and the right lever is HEAT. I can test that the switch is getting power to it via a 4-wire connector that plugs directly into the back of the switch. Power comes from a 10 Amp fuse on the Fuse Panel labeled HEATER / B.U. LPS. Fuse is good, and power is going through it. Any suggestions?
On a separate issue, the Heater Control Bulb was not working either. Found out that the 3A fuse on the Fuse Panel labeled PANEL LPS, which the heater lamp wire was plugged into, had no power. Moved the heater lamp power wire/connector on the fuse panel to another 3A fuse labeled RADIO / BRAKE LP, This fuse had power when the ignition switch is turned on. After making this wiring switch, my heater control lamp worked. Question: Any ideas why there is no power on the PANEL LPS fuse/circuit. Where does power come from for that panel fuse. Can't tell from looking at the front of the fuse panel. |
#2
|
||||
|
||||
Re: 66 GMC Heater control/switch not working
Are you saying the fan isn't working? Could it just be a bad fan motor?
__________________
Step by steps: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Some people are like slinkys. Not worth much but funny as heck when pushed down stairs. __________________ If the women don't find you handsome, they should at least find you handy. |
#3
|
|||
|
|||
Re: 66 GMC Heater control/switch not working
Yes, it could be the fan. Where is the fan and how do you get to it?
|
#4
|
||||
|
||||
Re: 66 GMC Heater control/switch not working
im about 200 miles from Cecilia right now but in this pic from my build thread you can see a metal contraption above the passenger footwell. I believe that's the motor housing.
__________________
Step by steps: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. Some people are like slinkys. Not worth much but funny as heck when pushed down stairs. __________________ If the women don't find you handsome, they should at least find you handy. |
#5
|
|||
|
|||
Re: 66 GMC Heater control/switch not working
Quote:
Quote:
|
#6
|
|||
|
|||
Re: 66 GMC Heater control/switch not working
All of my lighting problems were grounds.
Is there a pinout for the heater slider switch? Is there an actual ground wire. Or does the metal fan housing (if properly grounded) serve as the ground connection? |
#7
|
|||
|
|||
Re: 66 GMC Heater control/switch not working
I do not have the wiring manual for your truck so I would not know. On my 64 it is grounded to the body of the motor. If your is the same then the motor to the blower housing and to the cab should have a good ground.
|
Bookmarks |
Thread Tools | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Wanted 60-63 Heater control parts | AZKen | 1960-1966 GMC Marketplace | 0 | August 23rd, 2022 03:50 AM |
'60 deluxe heater control levers | jbgroby | Interiors, Dash, Lights and Electrical | 10 | December 23rd, 2018 10:30 PM |
Heater dashboard control assembly | Archiver | Previous Forum Posts | 0 | January 12th, 2009 01:32 AM |
Heater control pad for my Tilt cab? | Archiver | Previous Forum Posts | 0 | May 4th, 2004 06:45 AM |
Heater Control Questions | Archiver | Previous Forum Posts | 0 | February 24th, 2004 01:51 AM |