6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > General Discussion
#Sponsored

General Discussion Sit down and chat with fellow members! Any topics that don't fit other categories goes here.

Reply
 
Thread Tools
  #1  
Old July 22nd, 2023, 11:40 PM
jgpnashville jgpnashville is offline
Junior Member
 
Join Date: Mar 2023
Location: Nashville, TN
Truck: 1967 K15 305E
Age: 55
Posts: 20
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 17
jgpnashville is on a distinguished road
Default Protect-O-Plate Decode 1967 K15

I found and scanned the Protect-O-Plate from my 1967 K15 today and I'm trying to figure out what all the numbers mean.
I know the VIN is the first two numbers and "305E" is the engine. I think 464657 is the serial number from the engine.
"RXSTD" would seem to refer to the rear axle as being a standard and "3.54" would be the rear ratio, right?
"ID56885" should match the rear axle serial #.
"TRSM318" refers to the transmission type, which I am pretty sure is an SM420 (manual 4-speed with 7.05:1 low first gear). What does the "P" after "GMC" mean? It doesn't seem to line up with anything.

Any ideas? Have I gotten anything wrong in the list above?
Attached Images
File Type: png Protect-O-Plate reverse angle.png (498.3 KB, Multiple views, 11 clicks)
Reply With Quote
  #2  
Old July 23rd, 2023, 01:29 AM
Ed Snyder's Avatar
Ed Snyder Ed Snyder is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Medford, Oregon
Truck: 1962, 1967
Posts: 885
Thanks: 0
Thanked 4 Times in 2 Posts
Rep Power: 350
Ed Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura about
Default Re: Protect-O-Plate Decode 1967 K15

Quote:
Originally Posted by jgpnashville View Post
I found and scanned the Protect-O-Plate from my 1967 K15 today and I'm trying to figure out what all the numbers mean.
I know the VIN is the first two numbers and "305E" is the engine. I think 464657 is the serial number from the engine.
"RXSTD" would seem to refer to the rear axle as being a standard and "3.54" would be the rear ratio, right?
"ID56885" should match the rear axle serial #.
"TRSM318" refers to the transmission type, which I am pretty sure is an SM420 (manual 4-speed with 7.05:1 low first gear). What does the "P" after "GMC" mean? It doesn't seem to line up with anything.

Any ideas? Have I gotten anything wrong in the list above?
The SM318 is a three speed transmission. If you've got an NP420 four speed now, a previous owner must have replaced the three speed. You can find more VIN info at http://6066gmcguy.com/VinNumber.html and http://6066gmcguy.com/GMC-vin-list-6769.html
__________________
Ed Snyder
Medford, Oregon
1962 1000 Pickup 401M & Muncie 318 with overdrive
1962 K1000 Suburban 401M & SM420
1967 CM1500 pickup 351E & NP435
Reply With Quote
  #3  
Old July 23rd, 2023, 03:10 PM
George Bongert George Bongert is offline
Senior Member
 
Join Date: Jan 2013
Location: Oshkosh Wisconsin
Truck: Former owner Repowered by GMC 305 V-6, 1963 Chevy 30 Series SM420 Long Bed (9') Step/Fenderside
Posts: 213
Thanks: 0
Thanked 1 Time in 1 Post
Rep Power: 145
George Bongert will become famous soon enoughGeorge Bongert will become famous soon enoughGeorge Bongert will become famous soon enough
Default Re: Protect-O-Plate Decode 1967 K15

Quote:
Originally Posted by jgpnashville View Post
I found and scanned the Protect-O-Plate from my 1967 K15 today and I'm trying to figure out what all the numbers mean.
I know the VIN is the first two numbers and "305E" is the engine. I think 464657 is the serial number from the engine.
"RXSTD" would seem to refer to the rear axle as being a standard and "3.54" would be the rear ratio, right?
"ID56885" should match the rear axle serial #.
"TRSM318" refers to the transmission type, which I am pretty sure is an SM420 (manual 4-speed with 7.05:1 low first gear). What does the "P" after "GMC" mean? It doesn't seem to line up with anything.

Any ideas? Have I gotten anything wrong in the list above?
Greetings, Nashville!

TRSM318 indicates that the truck was equipped with a three speed transmission. If the plate had read TRSM420, that would be the code for the four speed transmission.
Reply With Quote
  #4  
Old July 23rd, 2023, 04:55 PM
jgpnashville jgpnashville is offline
Junior Member
 
Join Date: Mar 2023
Location: Nashville, TN
Truck: 1967 K15 305E
Age: 55
Posts: 20
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 17
jgpnashville is on a distinguished road
Default Re: Protect-O-Plate Decode 1967 K15

That's exactly what I thought, but that's not consistent with everything I know about the truck. The first and only owner prior to me was my employer. The truck was bought in 1967 as a work truck and sat unused for the past 20+ years until I resurrected it this year. I have the original bill of sale with all the info from a long-defunct dealership here in Nashville. It lists the truck with "305E Motor, 4 speed trans, 4 Wheel Drive, etc" so the SM420 4-speed would appear to have been the transmission that GMC shipped it with, unless the dealer swapped transmissions prior to sale. That seems unlikely, but not beyond possibility. Perhaps the Protect-O-Plate is in error?

I know the truck cost $2,938.65 when new and was purchased on 13 Oct 1967, presumably as the last-of-stock on '67 model year, since the '68 models would have been out at that point.

Thanks for all the thoughts.
Reply With Quote
  #5  
Old July 24th, 2023, 01:23 AM
Ed Snyder's Avatar
Ed Snyder Ed Snyder is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Medford, Oregon
Truck: 1962, 1967
Posts: 885
Thanks: 0
Thanked 4 Times in 2 Posts
Rep Power: 350
Ed Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura about
Default Re: Protect-O-Plate Decode 1967 K15

Quote:
Originally Posted by jgpnashville View Post
That's exactly what I thought, but that's not consistent with everything I know about the truck. The first and only owner prior to me was my employer. The truck was bought in 1967 as a work truck and sat unused for the past 20+ years until I resurrected it this year. I have the original bill of sale with all the info from a long-defunct dealership here in Nashville. It lists the truck with "305E Motor, 4 speed trans, 4 Wheel Drive, etc" so the SM420 4-speed would appear to have been the transmission that GMC shipped it with, unless the dealer swapped transmissions prior to sale. That seems unlikely, but not beyond possibility. Perhaps the Protect-O-Plate is in error?

I know the truck cost $2,938.65 when new and was purchased on 13 Oct 1967, presumably as the last-of-stock on '67 model year, since the '68 models would have been out at that point.

Thanks for all the thoughts.
In my opinion, it's unlikely the factory mis-labeled the transmission. More likely is that the original owner found the new truck on the dealer's lot and asked for the trans swap. Back then it was common for dealers to do things like that. For example, before he took delivery, my Dad had the dealer swap the 305 for a 351 and install an auxiliary two speed transmission in my one ton Suburban.
__________________
Ed Snyder
Medford, Oregon
1962 1000 Pickup 401M & Muncie 318 with overdrive
1962 K1000 Suburban 401M & SM420
1967 CM1500 pickup 351E & NP435
Reply With Quote
Reply

Bookmarks

Tags
protect-o-plate, protectoplate

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
1967 gmc dbrown1992 General Discussion 34 April 9th, 2016 09:57 PM
1967 flexplate # Archiver Previous Forum Posts 0 March 1st, 2006 03:26 AM
1967 for sale Archiver Previous Forum Posts 0 January 19th, 2005 12:29 AM
RE: 1967 engines Archiver Previous Forum Posts 0 March 6th, 2002 12:29 AM
RE: 1967 engines Archiver Previous Forum Posts 0 March 4th, 2002 12:22 AM


All times are GMT +1. The time now is 10:22 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 771728828974|1727688132|0