6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Wheels, Tires, Suspension and Brakes


Wheels, Tires, Suspension and Brakes Keep them doggies rollin', rawhide

Reply
 
Thread Tools
  #1  
Old April 18th, 2013, 07:34 PM
Paul in Nola Paul in Nola is offline
Junior Member
 
Join Date: Jan 2013
Location: New Orleans, LA
Truck: 1961 Stepside
Age: 77
Posts: 3
Rep Power: 0
Paul in Nola is on a distinguished road
Smile Replacement parking brake cable for 1961

The following is an account of my experiences replacing a front parking brake cable on a 61 GMC Short Bed.
Upon receiving my Front Parking Brake Cable from LMC Truck (ordered Monday afternoon, arrived late Wednesday or very early Thursday with regular shipping), part #34-3816, $49, $10 shipping, I first compared it with the old one I had removed on Monday for Length. Seemed to be the same or close enough. Next I checked the yoke where it pins to the Hand Brake lever. Was very tight so a bent it a smidgen and it fit well. Next checked the inside bracket that holds the cable housing in place and the clamp needed to be opened up a little which I did and again made fit. Same for the outside one that bolts to the frame. I then went to the threaded end of the cable and since no nuts were supplied with the cable tried the ones I removed. One went on with a little oil and I worked it back & forth so it was finger loose the whole length. The other locked up within 2 thread lengths and was really beat from removal. I went to Harry's Ace Hardware and using the good one to measure found that it was a 5/16X24 pitch which is a odd size that Harry's didn't carry. I found a automotive stud that had one end 5/16X24 that my good nut fit and got that to use as a chase and also got a longer 5/16 bolt to hold the outside cable housing holder where it bolts to the frame as I had to open the clamp so much to get the housing into the clamp that the original bolt left me no room to start the nut. Back at my house I put the stud in my vise, started the bad nut and with lots of oil worked it back and forth until free. When I put it on the threaded end of the cable it was still not finger loose so I worked it back and forth again the full length of the threaded end of the cable. Still not as loose as I would like but would have to do. After doing all these things I began to install it and it went fairly easily, but would have gone a lot better if the nuts had been supplied with the new cable as they are such a odd size and it did cost $50. All back together and seems to work fine! Really the nuts should be supplied as anybody is going to really beat up the old ones getting them off. I sprayed mine with Blaster penetrating oil and also wire brushed them prior to removal and they still came hard and took awhile to get off and the one ended up knurled in the process.
Reply With Quote
Reply

Bookmarks

Tags
parking brake

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Brake parts for a 1964 GMC model 1000 parking brake cable removing. Archiver Previous Forum Posts 9 November 5th, 2012 04:26 AM


All times are GMT +1. The time now is 10:52 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 861638455557|1637617938|0
Feedback Buttons provided by Advanced Post Thanks / Like (Lite) - vBulletin Mods & Addons Copyright © 2021 DragonByte Technologies Ltd.