Pay Dues or become a Site Supporter |
|
Transmissions and Rear Ends Three on the tree or four in the floor? Shift it all here. |
|
Thread Tools |
#1
|
|||
|
|||
62 GMC 1000 Panel - which clutch throwout bearing?
I failed to measure my TO bearing when I had to pull the engine last (replaced front and rear cylinder head freeze plugs, firewall side were disentegrated). Now on looking them up, I see there is a long style and three short versions all from the same manufacturer. I seem to think from recollection that it may be the long style.
Can anyone verify this or simply tell me that all of these listed for my model on Rock Auto could possibly have been used depending on transmission or clutch type? It had an SM318 3ott, then T5, then SM318 when I got it, blew that up and put in a Saginaw 4 speed with existing TO bearing. Now looking to swap an Aisin AX15 5 speed or possibly A833/NP440 MY6 with gm bell pattern. 305D swapping to 351C next time I pull engine to swap in disc brake crossmember.
__________________
Chuck in Ohio *'62 GMC 1000 Panel Truck - 305D/Saginaw 4sp soon: 351C V6 + AX15 5sp OD trans, & 73-87/91 disc brake front end, rear Cadillac calipers/ AWD Astro rotors, Dana 44 redrilled to 5 lug *'88 Suzuki Samurai 4x4 project, VW 1.9L mTDI turbodiesel, Toyota V6 LandCruiser drivetrain, full floater axles, future LWB bed stretch *'77-'79 Suzuki GS motorcycles, '76 Rickman CR900 roadracer. *Dirtbikes: 2 Kawasaki KDX220R's, '77 Suzuki PE250, '83 PE175 |
#2
|
||||
|
||||
Re: 62 GMC 1000 Panel - which clutch throwout bearing?
Long throwout vs. short is dependent upon the pivot point for the clutch. There are two sizes, a long one and a short one.
I seem to recall if it is the short pivot, then the long throw out. you show two diameters of clutch slave, those I can't advise on.
__________________
-- - David R Leifheit in Dallas, Oregon mailto: To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts. (2) 1961 1500 1962 1000 1963 2500 1963 4000 1964 2500 |
#3
|
|||
|
|||
Re: 62 GMC 1000 Panel - which clutch throwout bearing?
Ahhhh... you just reminded me that the pivot ball is worn out as well...
Any idea on a part number or source for those? Standard GM part that is fairly universal?
__________________
Chuck in Ohio *'62 GMC 1000 Panel Truck - 305D/Saginaw 4sp soon: 351C V6 + AX15 5sp OD trans, & 73-87/91 disc brake front end, rear Cadillac calipers/ AWD Astro rotors, Dana 44 redrilled to 5 lug *'88 Suzuki Samurai 4x4 project, VW 1.9L mTDI turbodiesel, Toyota V6 LandCruiser drivetrain, full floater axles, future LWB bed stretch *'77-'79 Suzuki GS motorcycles, '76 Rickman CR900 roadracer. *Dirtbikes: 2 Kawasaki KDX220R's, '77 Suzuki PE250, '83 PE175 |
Bookmarks |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Re: [6066 GMC] 66 gmc clutch,pressure plate and throwout bearing | Archiver | Previous Forum Posts | 0 | March 24th, 2006 09:36 AM |
Re: [6066 GMC] 66 gmc clutch,pressure plate and throwout bearing | Archiver | Previous Forum Posts | 0 | March 24th, 2006 05:20 AM |
Re: [6066 GMC] 66 gmc clutch,pressure plate and throwout bearing | Archiver | Previous Forum Posts | 0 | March 24th, 2006 02:35 AM |
Re: [6066 GMC] 66 GMC clutch, pressure plate & throwout bearing | Archiver | Previous Forum Posts | 0 | March 24th, 2006 12:57 AM |
66 gmc clutch,pressure plate and throwout bearing | Archiver | Previous Forum Posts | 0 | March 23rd, 2006 03:31 AM |