6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > GMC V6 and V12 Engines
#Sponsored

GMC V6 and V12 Engines Engine repair and rebuilding

Reply
 
Thread Tools
  #1  
Old May 16th, 2013, 07:51 PM
Foley Foley is offline
-= Site Supporter =-
 
Join Date: Apr 2013
Location: Greenwood, CA
Truck: 1964 1502 Fenderside
Posts: 173
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 115
Foley is on a distinguished road
Question 305e Start Up.

I'm working on a 1964 1502 that was used very hard as a ranch work truck it's whole life. Odometer reads 52,640. It was last registered in 1989 and has been sitting quietly inside a big barn for the past 23 years. I don't think the original owner ever changed the oil more than a couple times. I'm doing some start up maintenance and repair to get it running again. I drained the oil and pulled the pan to check the oil pump. The oil was thick with minor traces of fine dirt. Same in the filter cartridge. Oil pump screen somewhat clogged but cleaned up ok. The bottom of the pan had about an inch of peanut butter like crud but no metal parts which is good! Any suggestions out there about cleaning the engine further without doing a teardown? In the antique tractor world it's not uncommon to take one that has been sitting for many years and after getting the old stuff out, to overfill the crankcase or a transmission with diesel fuel and then pull it around at very slow rpm for about 5 minutes to flush everything inside. Anybody ever do that? And what about the new oil? Non detergent? High detergent for cleaning and breakdown of sludge? What do you guys recommend? tks. Bob Currie in Northern CA.

Last edited by Foley; May 16th, 2013 at 07:53 PM. Reason: grammar
Reply With Quote
  #2  
Old May 17th, 2013, 04:24 PM
raycow raycow is offline
Senior Member
 
Join Date: Jan 2013
Location: San Francisco, CA
Truck: 1960 C-10 Short Fleet
Posts: 129
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 105
raycow is on a distinguished road
Default Re: 305e Start Up.

This may sound extreme, but maybe not if you are really worried about crud in the oil system. Make a shaft to drive the oil pump with an electric drill. Change the oil and filter. Get a helper so you can spin the pump and turn the engine by hand at the same time.

Ray
Reply With Quote
  #3  
Old May 17th, 2013, 05:42 PM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,783
Thanks: 22
Thanked 6 Times in 5 Posts
Rep Power: 570
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: 305e Start Up.

Putting diesel in the motor is a pretty common thing when theyre gummed up or stuck. Thats what Id do if I was worried about sludge in the motor.

For the oil heres a link to my question that was dang near the same thing. Lots of opinions but generally high zinc is preferred.

http://6066gmcclub.com/forum/showthread.php?t=47432
Reply With Quote
  #4  
Old May 18th, 2013, 05:27 PM
Andice's Avatar
Andice Andice is offline
Senior Member
 
Join Date: Mar 2013
Location: Austin, TX
Truck: 1964 Fenderside 1000
Posts: 158
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 112
Andice is on a distinguished road
Default Re: 305e Start Up.

Ditto
Reply With Quote
  #5  
Old May 18th, 2013, 09:13 PM
Foley Foley is offline
-= Site Supporter =-
 
Join Date: Apr 2013
Location: Greenwood, CA
Truck: 1964 1502 Fenderside
Posts: 173
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 115
Foley is on a distinguished road
Default Re: 305e Start Up.

thanks for the repies. Ummm,,"ditto" Ditto to what? But about your comments on the oils there F.M.A.P. man, the kinds of oil to use after things are cleaned up in there is like the earlier thread you mentioned. Zinc, other chemicals, the API service offered by the various oil brands,,we could talk forever on that topic I'm sure. But I'd appreciate anybodies opinions on the oils to use. Using the diesel swish/wash inside cleans a lot of junk out of there, but there is always two sides to that discussion also. Some say it does a great job as long as you let things drip and dry out for 3 or 4 days after the wash out. Others argue that it will loosen up too much of the sludgie gunk that is holding an old worn engine together. After the clean out and then putting in fresh detergent oil, there is a strong possibility you'll start getting clattering and clanking from things like bearings, pistons, wrist pins, lifters, etc., plus the possibility of it starting to burn oil. But I guess it's fair to say that if you don't want to do a tear down and try some of these ideas, you get what you get. right?
Reply With Quote
  #6  
Old May 19th, 2013, 03:29 PM
Cayoterun's Avatar
Cayoterun Cayoterun is offline
Senior Member
 
Join Date: Jan 2013
Location: Guymon, Ok.
Truck: GMC V12 powered '46 Chevy pu
Age: 84
Posts: 167
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 117
Cayoterun is on a distinguished road
Default Re: 305e Start Up.

What ever you use, if too much gunk turns loose too fast, there's always the danger of plugging the oil pump screen. Change oil often after flushing.
I've had good results with using a light weight, cheap, high detergent oil, and changing oil and filter when color on dipstick gets dark.

Good luck and enjoy the ol' girl.
It's good to see people bring them back out of a long hibernation like you have.
__________________
Cayoterun
Okla Panhandle

I think I'll fix it myself, and pay the extra $500.
Reply With Quote
  #7  
Old May 19th, 2013, 07:02 PM
pasadenajim pasadenajim is offline
-= Extreme Supporter =-
 
Join Date: Jan 2013
Location: Phoenix, AZ
Truck: 1965 K1500
Posts: 76
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 92
pasadenajim is on a distinguished road
Default Re: 305e Start Up.

Once all the heavy lifting is done, clean out oil pan, oil pump and pick screen and check the distributor for wear then pan filled with oil you can use a drill to turn the shaft thus priming the system. Hook up a battery to the starter and ground and while the drill is priming the oiling system use a hand held switch to activate the starter (remove the spark plugs first) and in just a minute or two you can prime the entire system. You may want to remove a valve cover to actually see oil coming up thru the pushrods and also make sure the valves are moving in proportion to one another. Hope this helps and best of luck with your iron.
Reply With Quote
  #8  
Old July 17th, 2013, 07:07 PM
huntaaar huntaaar is offline
Temporarily Suspended
 
Join Date: Jul 2013
Location: grand rapids
Truck: 1967 c2500
Age: 35
Posts: 13
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
huntaaar is on a distinguished road
Default Re: 305e Start Up.

YIKES! should i be using a zinc additive? im running 5w30 in my 305e. i cleaned the lifter valley the other day and it had A SOLID INCH of oil gunk! that explains why my oil is always black even right after an oil change. help me out guys. what oil and what additive? thank you
Reply With Quote
  #9  
Old July 17th, 2013, 11:32 PM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,783
Thanks: 22
Thanked 6 Times in 5 Posts
Rep Power: 570
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: 305e Start Up.

Quote:
Originally Posted by huntaaar View Post
YIKES! should i be using a zinc additive? im running 5w30 in my 305e. i cleaned the lifter valley the other day and it had A SOLID INCH of oil gunk! that explains why my oil is always black even right after an oil change. help me out guys. what oil and what additive? thank you
back when these motors were made you had a lot of zinc in the oils. Gub'ment got involved and saw that was good so they "fixed" it and now all the zinc is about gone.

Since you just did an earl change you can put this stuff or something like it in there. Any high zinc oil additive is good. They run about $10 bucks

Last edited by FetchMeAPepsi; July 17th, 2013 at 11:46 PM. Reason: for some reason i said zinc in the motors. Motors arent made of zinc. Brain cramp.
Reply With Quote
  #10  
Old July 18th, 2013, 05:22 AM
donrm donrm is offline
Member
 
Join Date: Mar 2013
Location: Cincinnati,Ohio
Truck: 1966 1/2 ton fleetside 8' bed
Age: 68
Posts: 43
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 83
donrm is on a distinguished road
Wink Re: 305e Start Up.

I do not think I would try all diesel fuel. Back in the early 70's I would buy old cars to re-sell. I had the best luck putting new oil and make part of your oil change I would add 1-2 quarts of ATF, I would put 75-100 miles. change the oil, & never had fear of washing out your bearings. Don Maurath 1966 GMC 8' fleetside 351E
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
HEI conversion about to start Archiver Previous Forum Posts 7 November 7th, 2011 02:04 AM
Hot Start Archiver Previous Forum Posts 1 February 8th, 2011 04:35 AM
Re: Still won't start Archiver Previous Forum Posts 0 October 11th, 2003 03:16 AM
Still won't start Archiver Previous Forum Posts 0 October 10th, 2003 03:22 PM


All times are GMT +1. The time now is 04:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 921731456399|1730346988|0