6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Toro Flow Diesel Engines
#Sponsored

Toro Flow Diesel Engines For GMCs that came with the Toro Flow Diesel Engines

Reply
 
Thread Tools
  #1  
Old October 8th, 2018, 07:39 PM
panningbros panningbros is offline
Junior Member
 
Join Date: Oct 2018
Location: Gibbon MN
Truck: 1967 GMC 4000 tilt cab
Age: 68
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
panningbros is on a distinguished road
Default 478 toroflow flywheel

I just pulled a 478 diesel out of a New Idea 705 Uni-harvester. These did not use a clutch. Just has a splined drive disc bolted onto the flywheel. Does anybody know if this flywheel will accept a truck pressure plate and clutch disc?
The flywheel has 12 holes at 3/8" dia where the disc bolted onto. The bolts are approx 14-1/8" CC across the middle. Thanks !
Reply With Quote
  #2  
Old October 15th, 2018, 06:06 PM
panningbros panningbros is offline
Junior Member
 
Join Date: Oct 2018
Location: Gibbon MN
Truck: 1967 GMC 4000 tilt cab
Age: 68
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
panningbros is on a distinguished road
Default Re: 478 toroflow flywheel

This is my 1st reply and I thought I'd get some sort of reply. Can I get an acknowledgement that this is going out? Thanks!
Reply With Quote
  #3  
Old October 15th, 2018, 06:29 PM
Ed Snyder's Avatar
Ed Snyder Ed Snyder is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Medford, Oregon
Truck: 1962, 1967
Posts: 889
Thanks: 0
Thanked 5 Times in 3 Posts
Rep Power: 351
Ed Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura aboutEd Snyder has a spectacular aura about
Default Re: 478 toroflow flywheel

Quote:
Originally Posted by panningbros View Post
This is my 1st reply and I thought I'd get some sort of reply. Can I get an acknowledgement that this is going out? Thanks!
Your posts are definitely going out. Unfortunately, I suspect most forum members have little to no expertise in your application. If Marti Sacks sees your post, he might be able to answer for the rest of us. Be patient!
__________________
Ed Snyder
Medford, Oregon
1962 1000 Pickup 401M & Muncie 318 with overdrive
1962 K1000 Suburban 401M & SM420
1967 CM1500 pickup 351E & NP435
Reply With Quote
  #4  
Old October 16th, 2018, 04:12 AM
bigblockv6 bigblockv6 is offline
Senior Member
 
Join Date: Jan 2013
Location: Rohnert Park, ca.
Truck: 1968 KM2500
Posts: 1,325
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 418
bigblockv6 will become famous soon enoughbigblockv6 will become famous soon enough
Default Re: 478 toroflow flywheel

A photo of the face of the flywheel may be a clue for some of us.
Reply With Quote
  #5  
Old October 16th, 2018, 01:38 PM
massey478 massey478 is offline
Member
 
Join Date: May 2013
Location: Warsaw, IN
Truck: 1969 4000 ToroFlow, Massey Ferguson 1100 with a 478, Payloader with a 305, all adapted in my shop
Age: 77
Posts: 36
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
massey478 is on a distinguished road
Default Re: 478 toroflow flywheel

Good Morning Guys! I have been seeing the post but my problem with an answer is I have two Toro-Flows but both are not out of the units to look at the flywheel. One is in a truck and the other in a Uni. I do have a 401 out of a Uni but I am hesitant to comment from looking at it at the risk something might be different from your diesel.
My thoughts would be that I would first look to see if the pilot bearing needed for the transmission shaft can be inserted. I would then try to find if someone had a pressure plate of the type you want to use to measure the bolt pattern and see if it matches your flywheel. I will take a look at the 401 today or tomorrow to see if I think it will adapt. I am not sure I can get to the back of it right now without lifting it out of its place but I will try. My Massey 1100 with the 478 gas in it is in front of it. The tractor needs a new battery which I intend to get today because wood cutting season is here and I need it for the 20,000 winch on the back for skidding trees. Then I can move it out of the way of the 401. I know the drive coupler is still attached to it. I can then try to find a pressure plate that will work. Some 401 engines I have had the dual disc clutch assembly on them which is entirely different from a single. I will reply as soon as I can.
Reply With Quote
  #6  
Old October 17th, 2018, 03:19 PM
panningbros panningbros is offline
Junior Member
 
Join Date: Oct 2018
Location: Gibbon MN
Truck: 1967 GMC 4000 tilt cab
Age: 68
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
panningbros is on a distinguished road
Default Re: 478 toroflow flywheel

Thanks for the responses. This is a winter project for me so I am not in a desperate hurry for this. We have to finish harvest first. I will try and post a picture of the flywheel face sometime. Thanks! Dave
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
478 flywheel? bluestreak1854 1960-1966 GMC Marketplace 5 October 3rd, 2020 05:25 AM
1966 Toroflow 478 in Craigs Archiver Previous Forum Posts 0 December 20th, 2009 07:28 AM
Re: 1966 Toroflow 478 in Craigs Archiver Previous Forum Posts 0 December 20th, 2009 01:44 AM
Re: [6066 GMC] 1966 Toroflow 478 in Craigs Archiver Previous Forum Posts 0 December 20th, 2009 01:19 AM


All times are GMT +1. The time now is 11:16 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 911731597221|1730412961|0