6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > GMC V6 and V12 Engines
#Sponsored

GMC V6 and V12 Engines Engine repair and rebuilding

Reply
 
Thread Tools
  #1  
Old February 16th, 2016, 11:02 PM
TJ's GMC's Avatar
TJ's GMC TJ's GMC is offline
Senior Member
 
Join Date: Mar 2015
Location: Cave Junction, Oregon
Truck: 1964 GMC 1500 LWB Wideside 305E V6.
Posts: 1,341
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 402
TJ's GMC is on a distinguished road
Default Too much timing?

So how much is too much on these big engines? Reason I ask is I had mine set at 8 degrees advanced and the motor was good there, but for some reason I am not getting any Vacuum advance. I can tell this by using a timing light and disconnecting and reconnecting the vacuum hose and it makes absolutely no difference at idle. My 292 I6 would sound completely different when I did that. So my engine has been relying on mechanical advance...which seems to be fine as it's very responsive and pulls nicely.
Today I bumped my timing up to 12 degrees advanced and the motor sounds even better...more responsive all around and seems to idle smoother. I haven't driven it yet, but was wondering...you guys think 12 is to much? I know the factory setting is 6 degrees, but I'm getting no vacuum advance at idle. Carb is a 600 cfm edelbrock and works fine. Engine vacuum is 18 what ya call its. lol
__________________
"Excuse the rust I use my truck"
1964 GMC 1500 305E/sm420 4 barrel intake mod and dual exhaust.
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

1964 Chevy C20 292/SM420
1966 Chevy C10 292 hotrod 6/TKO600


My youtube channel aka Military Chevy:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #2  
Old February 17th, 2016, 02:20 PM
Clarke Clarke is offline
Senior Member
 
Join Date: Jan 2013
Location: Eureka Springs, AR
Truck: 1962 1500 Wideside 4 speed (305D / SM-420)
Posts: 217
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 131
Clarke is on a distinguished road
Default Re: Too much timing?

TJ, check out my thread named "Stock 305D Dyno Results". (Sorry I don't know how to insert a tread link inside a post.) I'm still running mine the same as noted within the last post. I do a lot of towing too and it runs great; no pinging, etc.

FYI, I've had my truck for six or seven years and I have the same 'lack of vacuum at the distributor at idle' you've noted. I don't believe I have ever brought it up here, so I'm curious to see what you find out. My intake vacuum is 20.

All other engines I have worked on (I6 & 4 bangers), there is a noticeable difference when disconnecting the vacuum advance line.
Reply With Quote
  #3  
Old February 18th, 2016, 09:20 AM
George Bongert George Bongert is offline
Senior Member
 
Join Date: Jan 2013
Location: Oshkosh Wisconsin
Truck: Former owner Repowered by GMC 305 V-6, 1963 Chevy 30 Series SM420 Long Bed (9') Step/Fenderside
Posts: 213
Thanks: 0
Thanked 1 Time in 1 Post
Rep Power: 145
George Bongert will become famous soon enoughGeorge Bongert will become famous soon enoughGeorge Bongert will become famous soon enough
Default Re: Too much timing?

Quote:
Originally Posted by TJ's GMC View Post
So how much is too much on these big engines? Reason I ask is I had mine set at 8 degrees advanced and the motor was good there, but for some reason I am not getting any Vacuum advance. I can tell this by using a timing light and disconnecting and reconnecting the vacuum hose and it makes absolutely no difference at idle. My 292 I6 would sound completely different when I did that. So my engine has been relying on mechanical advance...which seems to be fine as it's very responsive and pulls nicely.
Today I bumped my timing up to 12 degrees advanced and the motor sounds even better...more responsive all around and seems to idle smoother. I haven't driven it yet, but was wondering...you guys think 12 is to much? I know the factory setting is 6 degrees, but I'm getting no vacuum advance at idle. Carb is a 600 cfm edelbrock and works fine. Engine vacuum is 18 what ya call its. lol

Greetings TJ! The diaphragm in your vacuum advance is either cracked, or has a hole in it which will not allow it to work. I don't think 12 dgrees advance is excessive, however, I would replace the vaccum advance and reset the timing to 6 to 8 degrees BTDC.
Reply With Quote
  #4  
Old February 18th, 2016, 06:07 PM
TJ's GMC's Avatar
TJ's GMC TJ's GMC is offline
Senior Member
 
Join Date: Mar 2015
Location: Cave Junction, Oregon
Truck: 1964 GMC 1500 LWB Wideside 305E V6.
Posts: 1,341
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 402
TJ's GMC is on a distinguished road
Default Re: Too much timing?

Thanks for the replies guys! 12 degrees ended up being just a tad too much as I noticed cold starts became more involved. lol So I backed the timing down to somewhere's between 8-10. I'll be sure to check the dizzy and see what's going on, FWIW, it is a brand new one from Autozone.
__________________
"Excuse the rust I use my truck"
1964 GMC 1500 305E/sm420 4 barrel intake mod and dual exhaust.
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

1964 Chevy C20 292/SM420
1966 Chevy C10 292 hotrod 6/TKO600


My youtube channel aka Military Chevy:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #5  
Old February 19th, 2016, 06:42 AM
TJ's GMC's Avatar
TJ's GMC TJ's GMC is offline
Senior Member
 
Join Date: Mar 2015
Location: Cave Junction, Oregon
Truck: 1964 GMC 1500 LWB Wideside 305E V6.
Posts: 1,341
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 402
TJ's GMC is on a distinguished road
Default Re: Too much timing?

Quote:
Originally Posted by Clarke View Post
TJ, check out my thread named "Stock 305D Dyno Results". (Sorry I don't know how to insert a tread link inside a post.) I'm still running mine the same as noted within the last post. I do a lot of towing too and it runs great; no pinging, etc.

FYI, I've had my truck for six or seven years and I have the same 'lack of vacuum at the distributor at idle' you've noted. I don't believe I have ever brought it up here, so I'm curious to see what you find out. My intake vacuum is 20.

All other engines I have worked on (I6 & 4 bangers), there is a noticeable difference when disconnecting the vacuum advance line.
Alright, so I did a complete read up on that thread and that was some great info. Thanks for taking the time to write that up! Anyhow, When I had my timing set at 12 degrees advanced the first thing I noticed was quicker throttle response for sure. Motor even seemed to pull better, BUT when trying to cold start I was more involved and even when the engine was somewhat warm it was a bit harder to start. So I came home and backed the timing down to around 10. Need to drive it again and see what happens. Motor will probably be close to the same as before as 2 degrees more advanced doesn't make much difference. When advancing the timing I didn't get much of an RPM increase or decrease. I Do still need to check my vacuum advance as it made absolutely No difference at idle. My 292 would idle at 10 degrees without vacuum and 25 with vacuum....my 305 V6 idles at 10 with or without so something must be wrong.
__________________
"Excuse the rust I use my truck"
1964 GMC 1500 305E/sm420 4 barrel intake mod and dual exhaust.
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

1964 Chevy C20 292/SM420
1966 Chevy C10 292 hotrod 6/TKO600


My youtube channel aka Military Chevy:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #6  
Old February 19th, 2016, 02:57 PM
abus319 abus319 is offline
-= Site Supporter =-
 
Join Date: Sep 2013
Location: Austin Texas
Truck: 1960 3500, 305D heads
Posts: 116
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 99
abus319 is on a distinguished road
Default Re: Too much timing?

The vacuum advance issue has been puzzling me as well.
I checked the 478 with a hand operated pump before I fired it up, and found that it didn't start to operate until about 24 inches. That got me curious so I checked the 305's and found about the same thing. Basically they never operate.
I hope someone can shed some light on this
Reply With Quote
  #7  
Old February 19th, 2016, 10:27 PM
Clyde Clyde is offline
Member
 
Join Date: Jan 2013
Location: Abbeville,SC
Truck: 1961 GMC Suburban 4WD-1966 GMC p?u,351,Turbo 400
Age: 82
Posts: 74
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 98
Clyde will become famous soon enough
Default Re: Too much timing?

On the 305 initial timing is set at 7.5 degrees, the vacuum advance has a total of 18 degrees, starts to move at 5-7 inches of vacuum and achieves full advance at 12.25 - 13.5 inches. The centrifugal advance has a total of 30 degrees, 0-2 degrees at 800 rpm's, 11 degrees at 2000 rpm's and 30 at 3400 rpm's thus giving a potential of 55.5 degrees under full vacuum and an rpm of over 3400. On the 351 centrifugal advance is 26 degrees vacuum advance is 18 degrees and 5 degrees initial for a total of 49 degrees at 3500 rpm's. Hope this clears up any confusion, this is from the factory GMC shop manual.
__________________
Clyde McKaba
Abbeville,SC
1961 GMC Suburban 4WD 305 V6, 4spd
1966 GMC 3/4T P/U 351 V6, Turbo 400,Gear Vender OD
1969 GMC Suburban 1/2T
Reply With Quote
  #8  
Old February 19th, 2016, 10:55 PM
TJ's GMC's Avatar
TJ's GMC TJ's GMC is offline
Senior Member
 
Join Date: Mar 2015
Location: Cave Junction, Oregon
Truck: 1964 GMC 1500 LWB Wideside 305E V6.
Posts: 1,341
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 402
TJ's GMC is on a distinguished road
Default Re: Too much timing?

Thanks Clyde! I'm going to check that dizzy on the engine and see if the pump or something is jammed. Cause I'm not getting advance at all. Recently I looked that the pump's arm while reving the motor and there was no movement at all.
__________________
"Excuse the rust I use my truck"
1964 GMC 1500 305E/sm420 4 barrel intake mod and dual exhaust.
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

1964 Chevy C20 292/SM420
1966 Chevy C10 292 hotrod 6/TKO600


My youtube channel aka Military Chevy:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
  #9  
Old February 20th, 2016, 02:27 AM
Clarke Clarke is offline
Senior Member
 
Join Date: Jan 2013
Location: Eureka Springs, AR
Truck: 1962 1500 Wideside 4 speed (305D / SM-420)
Posts: 217
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 131
Clarke is on a distinguished road
Default Re: Too much timing?

TJ, I haven't noticed any change on how it starts. I drove it several years with the timing set per spec and after I advanced the timing it's much more responsive, yet starts the same. I drive mine during all seasons, even if it's 15 degrees or 100 degrees.

I swung by O'Riellys on my way home tonight to get a new vacuum advance, but they couldn't find the part number, so I need to do some research. If I still have the orig one, I wouldn't be surprised if the diaphram is stiff.

When I was a kid rebuilding honda car engines, an old timer taught me to advance the timing a few degrees, because it would make the engine start quicker. I don't know if it's true or not, but I did it anyway. Typically, I stick to the specs, untill I started playing around with this 305.
Reply With Quote
  #10  
Old February 20th, 2016, 02:37 AM
TJ's GMC's Avatar
TJ's GMC TJ's GMC is offline
Senior Member
 
Join Date: Mar 2015
Location: Cave Junction, Oregon
Truck: 1964 GMC 1500 LWB Wideside 305E V6.
Posts: 1,341
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 402
TJ's GMC is on a distinguished road
Default Re: Too much timing?

I was told to retard the timing for easier starts.

Have the initial timing around 10 now and it seems to be a little easier starting. Still got nice throttle response. Weather is real bad so I won't be out there. Ya know I remember putting the vacuum advance off of my 292's dizzy and onto the 305....and it kept advancing and retarding the timing all by itself....I could watch the arm move back and forth and back and forth and the motor never found a happy medium. But this brand new dizzy in.....nothing....no movement period...I can rev the engine all the time...nothing.
__________________
"Excuse the rust I use my truck"
1964 GMC 1500 305E/sm420 4 barrel intake mod and dual exhaust.
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

1964 Chevy C20 292/SM420
1966 Chevy C10 292 hotrod 6/TKO600


My youtube channel aka Military Chevy:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.
Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Timing Archiver Previous Forum Posts 1 May 28th, 2012 03:04 AM
Timing Archiver Previous Forum Posts 0 August 16th, 2008 02:17 AM
Timing Archiver Previous Forum Posts 0 August 16th, 2008 02:08 AM
RE: timing Archiver Previous Forum Posts 0 October 23rd, 2002 02:07 AM
Timing is everything Archiver Previous Forum Posts 0 March 4th, 2001 05:37 AM


All times are GMT +1. The time now is 10:43 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 951731943628|1730799791|0