6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Transmissions and Rear Ends
#Sponsored

Transmissions and Rear Ends Three on the tree or four in the floor? Shift it all here.

Reply
 
Thread Tools
  #1  
Old February 16th, 2023, 08:20 PM
JoelNC JoelNC is offline
Junior Member
 
Join Date: Sep 2020
Location: Raleigh, NC
Truck: 1964 Longbed 305
Posts: 17
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 32
JoelNC is on a distinguished road
Default 64 305E Clutch Not Engaging

I'm finishing up rebuilding a 64 305E. I have this clutch installed: https://www.rockauto.com/en/moreinfo...&pt=1993&jsn=9

It's a 3-on-the-tree and I don't think the clutch is fully engaging. The clutch linkages all adjusted as far as they go. Also have a new clutch fork. When I have it in gear and hold the clutch and engage the brake, the engine dies. (It's on jack stands right now.)

Any recommendations? I'm not sure how to proceed from here. This is the last thing before getting the truck back on the road (first time since 2000).
Reply With Quote
  #2  
Old February 16th, 2023, 08:35 PM
AZKen's Avatar
AZKen AZKen is offline
-= Dues Paid =-
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,647
Thanks: 0
Thanked 3 Times in 3 Posts
Rep Power: 527
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Re: 64 305E Clutch Not Engaging

Please explain what the test was.
Push clutch pedal in, start motor, put in gear, let clutch pedal out, wheels start turning, push on brake, motor dies??????? that would be normal.......or what is the sequence?
Please list each step like I did in my example. It sounds like you get it started and in gear but I don't know what "hold the clutch" means. Puch clutch pedal in like coasting, then apply brakes and motor stops. That would be "clutch not DISengaging"

Last edited by AZKen; February 16th, 2023 at 08:51 PM.
Reply With Quote
  #3  
Old February 16th, 2023, 08:44 PM
JoelNC JoelNC is offline
Junior Member
 
Join Date: Sep 2020
Location: Raleigh, NC
Truck: 1964 Longbed 305
Posts: 17
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 32
JoelNC is on a distinguished road
Default Re: 64 305E Clutch Not Engaging

Push clutch pedal in, start motor, put in gear, let clutch pedal out, wheels start turning, *push clutch in*, push on brake, motor dies
Reply With Quote
  #4  
Old February 16th, 2023, 08:54 PM
JoelNC JoelNC is offline
Junior Member
 
Join Date: Sep 2020
Location: Raleigh, NC
Truck: 1964 Longbed 305
Posts: 17
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 32
JoelNC is on a distinguished road
Default Re: 64 305E Clutch Not Engaging

Quote:
Originally Posted by AZKen View Post
Please explain what the test was.
Push clutch pedal in, start motor, put in gear, let clutch pedal out, wheels start turning, push on brake, motor dies??????? that would be normal.......or what is the sequence?

Please list each step like I did in my example. It sounds like you get it started and in gear but I don't know what "hold the clutch" means. Puch clutch pedal in like coasting, then apply brakes and motor stops. That would be "clutch not DISengaging"
Correct, that's what I think is happening. It's in gear, the wheels are turning. I push the clutch in and then press the brake in and the engine dies, so the clutch is not disengaging the engine?
Reply With Quote
  #5  
Old February 16th, 2023, 09:21 PM
AZKen's Avatar
AZKen AZKen is offline
-= Dues Paid =-
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,647
Thanks: 0
Thanked 3 Times in 3 Posts
Rep Power: 527
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Re: 64 305E Clutch Not Engaging

Yes, the adjustment rod needs adjusted to be "longer" to push fork lever more towards rear of truck. Therefore rocking fork forward and pushing throwout brearing deeper into clutch release springs.
It is possible that you have some components installed incorrectly. Sometimes throwout bearing is installed backwards by installer. Reducing it's "reach".....or put the disc in backwards....or throwout bearing facing correctly but flange not "under" the spring clips....and so on. These things WILL cause your failure to disengage problem. You say you have run out of adjustment so the items mentioned are possible.

Last edited by AZKen; February 16th, 2023 at 09:36 PM.
Reply With Quote
  #6  
Old February 16th, 2023, 09:35 PM
JoelNC JoelNC is offline
Junior Member
 
Join Date: Sep 2020
Location: Raleigh, NC
Truck: 1964 Longbed 305
Posts: 17
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 32
JoelNC is on a distinguished road
Default Re: 64 305E Clutch Not Engaging

I checked the throw out bearing, and it's good. Are adjustment rods available anywhere? Or, do you think I'd have luck fabricating a longer adjustment rod?
Reply With Quote
  #7  
Old February 16th, 2023, 09:45 PM
AZKen's Avatar
AZKen AZKen is offline
-= Dues Paid =-
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,647
Thanks: 0
Thanked 3 Times in 3 Posts
Rep Power: 527
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Re: 64 305E Clutch Not Engaging

I added some info, check it.

You checked the T/O bearing and it's good? Well something is wrong somewhere right? so you missed something right?

If you are all stock, you need to figure out what you did wrong or if you bought the correct stuff. If you start chasing your tail, then the clutch won't engage all the way and you will wear it out fast.

The clutch in our club list says 11" disc. Also shows a long and a short throwout bearing. Don't know what is correct. The Rockauto MU18621 shows application for GMC as 1961-1963. Has really good info at scroll down. Videos and pics of right and wrong install info. (hypertext links)

Last edited by AZKen; February 16th, 2023 at 10:39 PM.
Reply With Quote
  #8  
Old February 16th, 2023, 10:39 PM
JoelNC JoelNC is offline
Junior Member
 
Join Date: Sep 2020
Location: Raleigh, NC
Truck: 1964 Longbed 305
Posts: 17
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 32
JoelNC is on a distinguished road
Default Re: 64 305E Clutch Not Engaging

Here's some pictures. I removed the cotter pin prior to photo. Do i have the linkage backwards?




Reply With Quote
  #9  
Old February 16th, 2023, 10:44 PM
JoelNC JoelNC is offline
Junior Member
 
Join Date: Sep 2020
Location: Raleigh, NC
Truck: 1964 Longbed 305
Posts: 17
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 32
JoelNC is on a distinguished road
Default Re: 64 305E Clutch Not Engaging

And some photos of the truck...




Reply With Quote
  #10  
Old February 17th, 2023, 12:54 AM
Funky61's Avatar
Funky61 Funky61 is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Corona, CA
Truck: 1961 Suburban 1962 GMC Utility
Posts: 1,167
Thanks: 9
Thanked 8 Times in 5 Posts
Rep Power: 421
Funky61 is just really niceFunky61 is just really niceFunky61 is just really niceFunky61 is just really niceFunky61 is just really niceFunky61 is just really nice
Default Re: 64 305E Clutch Not Engaging

Looks like your missing the wedge



https://www.ebay.com/itm/30476267078...mis&media=COPY
Attached Images
File Type: jpeg 919303CF-9646-4240-A05D-F60E1884D5AD.jpeg (4.54 MB, Multiple views, 8 clicks)
__________________
1961 GMC Suburban 305A Overdrive
1962 GMC Utility 305D
Reply With Quote
Reply

Bookmarks

Tags
305e, clutch


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Re: [6066 GMC] Re: '64 305e clutch linkage failure Archiver Previous Forum Posts 0 July 18th, 2006 01:21 AM
Re: '64 305e clutch linkage failure Archiver Previous Forum Posts 0 July 17th, 2006 01:04 AM
Re: [6066 GMC] '64 305e clutch linkage failure Archiver Previous Forum Posts 0 July 16th, 2006 09:23 AM
Re: [6066 GMC] '64 305e clutch linkage failure Archiver Previous Forum Posts 0 July 16th, 2006 06:58 AM
'64 305e clutch linkage failure Archiver Previous Forum Posts 0 July 15th, 2006 01:42 AM


All times are GMT +1. The time now is 12:48 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 841730414881|1729208930|0