6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > General Discussion
#Sponsored

General Discussion Sit down and chat with fellow members! Any topics that don't fit other categories goes here.

Reply
 
Thread Tools
  #11  
Old February 9th, 2024, 04:58 PM
Prowbar Prowbar is offline
-= Dues Paid =-
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 454
Thanks: 12
Thanked 14 Times in 13 Posts
Rep Power: 204
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: clutch problem

Quote:
Originally Posted by FetchMeAPepsi View Post
Well there's your trouble! Your transmission is 70 lbs too heavy!
Feel free to crawl under my truck and bench press that SM420 a few times!
Reply With Quote
  #12  
Old February 10th, 2024, 02:44 PM
bigred1 bigred1 is offline
Junior Member
 
Join Date: Nov 2014
Location: Woodbridge, NJ
Truck: 1963 2500
Posts: 23
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 68
bigred1 is on a distinguished road
Default Re: clutch problem

thanks Jim a, I'll try that
Reply With Quote
  #13  
Old February 10th, 2024, 06:45 PM
Jim A Jim A is offline
Senior Member
 
Join Date: Jan 2013
Location: Potter Valley, CA
Truck: 1960 3/4, 4 spd, stepside
Posts: 157
Thanks: 0
Thanked 3 Times in 3 Posts
Rep Power: 118
Jim A is on a distinguished road
Default Re: clutch problem

It is important to make sure you have the full stroke range at both the master and slave cylinders.
There needs to be a little slack at the throwout bearing to protect it, but also enough travel of the slave rod to fully release the clutch disc.
I fought this situation for years and the fix. after waiting too long, was very difficult.
Reply With Quote
  #14  
Old February 10th, 2024, 07:18 PM
TRybas TRybas is offline
-= Dues Paid =-
 
Join Date: Apr 2020
Location: Croydon, PA
Truck: 1960 GMC Long fleet 4x4
Age: 37
Posts: 47
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 47
TRybas is on a distinguished road
Default Re: clutch problem

When you say you can’t get it into gear with the engine running I assume you mean the gears grind when you try to engage? I believe ‘63 was the same as my ‘60. Is it a sm420 with a hydraulic clutch?

Sounds to me like the flywheel is not disengaging which is throwing the synchro off. Try cycling through all the gears with the engine off. Ending in 4th. Than start it up and see if you can put it back into 4th. Also try pumping up the clutch a few times before shifting. May or may not work but could give you a better idea of what is going on.

There is an adjustment nut where the slave cylinder meets the fork. Try setting it out further. Or master/slave cylinders could be on there last leg. Get eyes on the slave cylinder when someone pumps the clutch and see how much travel you get.
Reply With Quote
  #15  
Old February 11th, 2024, 06:35 PM
bigred1 bigred1 is offline
Junior Member
 
Join Date: Nov 2014
Location: Woodbridge, NJ
Truck: 1963 2500
Posts: 23
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 68
bigred1 is on a distinguished road
Default Re: clutch problem

thanks for the info
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Problem with clutch disengaging Clarke Transmissions and Rear Ends 36 August 12th, 2022 03:15 AM
FS- Late Mechanical clutch bell housing, flywheel and clutch zigafomana 1960-1966 GMC Marketplace 11 April 1st, 2014 02:26 AM
6066gmc 60 model clutch problem Archiver Previous Forum Posts 0 July 4th, 2006 02:25 AM
Re: have a problem Archiver Previous Forum Posts 0 December 3rd, 2003 01:24 AM


All times are GMT +1. The time now is 07:11 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 691734025264|1732947098|0