6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Builds and Journals
#Sponsored

Builds and Journals This is where the magic happens. Photograph & document your GMC build progress for posterity.
NOTICE - Photobucket will delete your pics after a time. Use another host if possible.

Reply
 
Thread Tools
  #91  
Old June 17th, 2024, 07:50 PM
Prowbar Prowbar is offline
Senior Member
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 434
Thanks: 8
Thanked 10 Times in 9 Posts
Rep Power: 198
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: "Papa Smurf" - 1966 GMC 1500 Custom

Nice work on the brackets and reservoir. Never had any issues with coolant overflow.
The V6 takes 8 gallons of coolant (didn't believe it at first until it all pours in). When the engine is cold I cannot see any coolant in the radiator but when the engine is hot it is about 1" below the cap. Anymore coolant and it will blow it out via the hose under the cap.
I always drill a small (.080-.100") hole in the thermostat so air cannot get trapped between the thermostat.

As far as the blinker issue goes, did you check the harness in the steering column for any exposed wiring? Did you have the park lights on when the fuse went out?
Did you check/replace the hood harness?
Do you have a good ground from the hood to the rest of the truck?

IMO, as far as the drivetrain goes, I'd build up the 351 V6 and rebuild the NP435 transmission. They are sweet shifting units in good shape. The close ratio version is the best for the V6. Yours is probably the wide ratio.
Regear the rear end to 3.23 gears using the DoctorDiff gear set or install a Gear Vendors Overdrive.
Reply With Quote
  #92  
Old June 18th, 2024, 06:42 AM
LordNatedawg LordNatedawg is offline
Member
 
Join Date: Sep 2019
Location: Sparks, Nevada
Truck: 1966 GMC 1500 Custom
Age: 24
Posts: 73
Thanks: 0
Thanked 2 Times in 1 Post
Rep Power: 67
LordNatedawg will become famous soon enoughLordNatedawg will become famous soon enough
Default Re: "Papa Smurf" - 1966 GMC 1500 Custom

The 351 V6 and my 350 V8 are also running at different temperatures. On the factory gauge my operating temp is right on the edge of the normal line, closer to overheating. I've verified several different ways that around 200-210* is at that zone. I would guess that the V6 operates closer to 160-180*, because my 180* thermostat starts to open when the needle is dead center of the gauge. More heat is obviously going to mean more expansion. I keep my radiator full to the top to prevent oxidation.

My wiring issue is strange because everything is new. And I never had the blinker issue after installing the new column. The issue came about after I rewired the rest of the truck. I added ground straps all over. Battery to body, frame, and engine. Engine to frame, and frame to body. Also added a hood to body. When it blew the fuse while idling, there weren't any lights on in the truck. I did find that one of my switchback LEDs was slightly damaged. I installed some new ones and I'll just have to see if that helps or not. I really should take a multi-meter and try to find the short.

I also agree with you on the V6 and NP435, but I don't think I'm going to do it on this truck. I have my reasons, even if they may be frowned upon here. The V6 I picked up a few years ago will be used in a vehicle some day, but it won't be in Papa Smurf.
Reply With Quote
  #93  
Old July 1st, 2024, 01:51 AM
LordNatedawg LordNatedawg is offline
Member
 
Join Date: Sep 2019
Location: Sparks, Nevada
Truck: 1966 GMC 1500 Custom
Age: 24
Posts: 73
Thanks: 0
Thanked 2 Times in 1 Post
Rep Power: 67
LordNatedawg will become famous soon enoughLordNatedawg will become famous soon enough
Default Re: "Papa Smurf" - 1966 GMC 1500 Custom

I FINALLY FOUND MY BLINKER PROBLEM!!!!!!

Decided to do some more diagnosis today. I needed to be able to recreate the issue. I ran my truck with no lights on for 30 minutes. Nothing. I turned on the blinkers one by one. Left - pause - off - pause - right - pause - repeat. No dice. Then I moved on to the reverse.

Reverse - pause- neutral - pause - repeat. Suddenly I heard a loud POP when I switched to reverse. I swapped the fuse out and repeated. R - N - R - N - R -POP!

I ohmed out my reverse switch and found that it was very intermittently shorting to itself, creating a dead short to ground when I shifted into reverse. Suddenly everything makes sense. When I initially started my rewire, I noticed that the PO had no reverse light bulbs and no pigtail on the reverse switch. He must've been having this same issue.

Just about drove myself crazy trying to track this one down. I absolutely despise intermittent electrical issues. But now it has been uncovered. I'm going to try and find a new switch that fits in the shifter base. Hopefully this is the end of this problem.
Reply With Quote
The Following 2 Users Say Thank You to LordNatedawg For This Useful Post:
FetchMeAPepsi (July 1st, 2024), Prowbar (July 8th, 2024)
  #94  
Old July 1st, 2024, 03:28 AM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,774
Thanks: 16
Thanked 4 Times in 3 Posts
Rep Power: 568
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: "Papa Smurf" - 1966 GMC 1500 Custom

Awesome tracking skills! That must have drove you crazy and it was all due to a tiny little wire acting up.


To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

__________________
Step by steps:

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Some people are like slinkys. Not worth much but funny as heck when pushed down stairs.
__________________
If the women don't find you handsome, they should at least find you handy.
Reply With Quote
  #95  
Old July 1st, 2024, 04:59 PM
aphaynes's Avatar
aphaynes aphaynes is offline
-= Site Supporter =-
 
Join Date: Mar 2014
Location: Athens, AL
Truck: 1965 GMC 1000
Posts: 392
Thanks: 0
Thanked 1 Time in 1 Post
Rep Power: 168
aphaynes is on a distinguished road
Default Re: "Papa Smurf" - 1966 GMC 1500 Custom



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

Nice troubleshooting! Congrats.
__________________
My Stuff:

1965 GMC 1000, 305E

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


1970 Torino GT, 302
1973 Mach I Mustang, 351W
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
My new "find" - 62 K1000 big window short wide GMCNUT General Discussion 7 April 11th, 2019 08:46 PM
My 1963 1000 Factory Black true "Barn Find" GMCNUT General Discussion 4 April 5th, 2019 09:46 PM
"H" or "X" Pipe On A V6? 1972RedNeck GMC V6 and V12 Engines 12 August 8th, 2018 01:15 PM
GMC 2 ton 6cyl "Toro-Flow" Diesel. No title. Archiver Previous Forum Posts 4 July 21st, 2011 03:03 AM
"E", "H", and "J" Cab models Archiver Previous Forum Posts 2 May 20th, 2011 08:04 AM


All times are GMT +1. The time now is 07:04 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 781729009125|1727805848|0