6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Interiors, Dash, Lights and Electrical
#Sponsored

Interiors, Dash, Lights and Electrical Everything Inside

Reply
 
Thread Tools
  #1  
Old March 23rd, 2021, 06:10 AM
biscaynebirdie biscaynebirdie is offline
Junior Member
 
Join Date: Jan 2021
Location: Santa Rosa, California
Truck: 1965 1000 Series with 250 engine and SM420 transmission
Posts: 26
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 30
biscaynebirdie is on a distinguished road
Unhappy Overcharging alternator and buzzing voltage regulator

I keep blowing out flasher relays, oil pressure switches, and heater blower fuses in my truck, so I decided to check the voltage at the battery when at idle: 15-15.3 volts. The 1963 Chevrolet Truck Shop Manual says that 15 volts is the maximum voltage that should be had (generally, as I’m sure you all know, 12-14 is what is generally acceptable), so I have a feeling that this is probably why I keep ruining these various electrical components. I assumed it was time to purchase a new voltage regulator.

I drove down to O’Reilly and picked up a brand new regulator (made sure it was made in the USA) and decided to give it a try. With the key turned on, the generator light lit up as it should and went out when the engine started up. However, when I bumped up the RPMs just a little bit, the generator light turned on and a buzzing was heard coming from the voltage regulator. I checked the voltage while this was happening, and it was reading an astounding 16-17 volts and climbing! Not good... When I increased the RPMs a little bit more, the generator light turned off and the buzzing stopped (voltage returned to 15-15.3 volts). As I released the throttle, it buzzed again (generator light lit up as well) then stopped buzzing when at idle. I popped the cover off of the voltage regulator to check if I could see what was causing the buzz. It was, as I had assumed, the set of points that generally will be open before the engine starts and will close once running. I’ve included a picture of said points below (it’s circled in red, for ease of viewing).

I checked for good continuity in all wires in the area (voltage regulator, alternator, horn relay), as well as cleaned up all of the connectors (adding some good old dielectric grease, too). I made sure that the red wire that goes from the battery to the regulator was getting a full 12 volts, as well as checked for 12 volts on the brown wire with the key on and no volts with the key turned off. Hmm...

I’ve read that one possible culprit could be a bad diode in the alternator. Another culprit could be that my battery is at the end of its life. However, I’m not so sure about the latter since with the engine not running, the battery sends out a good 12.7-13.2 volts.

So... any ideas?
Attached Images
File Type: jpeg F4170C7C-99D2-4F14-B66E-3A09F21941ED.jpeg (1,006.9 KB, Multiple views, 5 clicks)
Reply With Quote
  #2  
Old March 23rd, 2021, 04:52 PM
biscaynebirdie biscaynebirdie is offline
Junior Member
 
Join Date: Jan 2021
Location: Santa Rosa, California
Truck: 1965 1000 Series with 250 engine and SM420 transmission
Posts: 26
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 30
biscaynebirdie is on a distinguished road
Default Re: Overcharging alternator and buzzing voltage regulator

This morning, I’ll try running a ground wire from the ground post on the alternator to the grounding screw at the regulator and see if it makes any difference. I currently have no wire connected to that post on my alternator (even though it should be grounded through the engine).
Reply With Quote
  #3  
Old March 23rd, 2021, 06:07 PM
biscaynebirdie biscaynebirdie is offline
Junior Member
 
Join Date: Jan 2021
Location: Santa Rosa, California
Truck: 1965 1000 Series with 250 engine and SM420 transmission
Posts: 26
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 30
biscaynebirdie is on a distinguished road
Default Re: Overcharging alternator and buzzing voltage regulator

Update: no change.
Reply With Quote
  #4  
Old March 24th, 2021, 03:18 AM
AZKen's Avatar
AZKen AZKen is offline
-= Dues Paid =-
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,644
Thanks: 0
Thanked 2 Times in 2 Posts
Rep Power: 527
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Re: Overcharging alternator and buzzing voltage regulator

I read you have an alternator with external voltage regulator. Not a generator. Either way..... Buy a Delco rebuilt 10si alternator and get rid of all that wiring, Delcotron alternator and voltage regulator. Hook up two wires and you are all fixed for about $50. Don't play around with old technology in this area.
Your battery will not last at 17+ volt charging. Free Ship May want to add This

Last edited by AZKen; March 24th, 2021 at 03:54 AM.
Reply With Quote
  #5  
Old March 24th, 2021, 04:55 AM
biscaynebirdie biscaynebirdie is offline
Junior Member
 
Join Date: Jan 2021
Location: Santa Rosa, California
Truck: 1965 1000 Series with 250 engine and SM420 transmission
Posts: 26
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 30
biscaynebirdie is on a distinguished road
Default Re: Overcharging alternator and buzzing voltage regulator

I’ve read that the one wire alternator is a major time saver. However, today I actually managed to get the original voltage regulator back in working order! 12.7 volts at idle, 13.5 volts around 1500 RPM, and goes about as high as 15 volts when I’m really giving it gas. Everything seems okay for now. If this doesn’t last, I’ll convert to the one wire alternator.
Reply With Quote
  #6  
Old March 24th, 2021, 06:20 PM
AZKen's Avatar
AZKen AZKen is offline
-= Dues Paid =-
 
Join Date: Jul 2014
Location: AZ
Truck: 6066GMC
Posts: 1,644
Thanks: 0
Thanked 2 Times in 2 Posts
Rep Power: 527
AZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really niceAZKen is just really nice
Default Re: Overcharging alternator and buzzing voltage regulator

I don't do one wire, just normal 2/3 wire. Hope all is good now. There is not much time savings in one wire really.
Reply With Quote
  #7  
Old March 24th, 2021, 10:04 PM
James James is offline
-= Extreme Supporter =-
 
Join Date: Jun 2013
Location: Greer, SC
Truck: 1964 GMC 1500 2wd
Age: 69
Posts: 449
Thanks: 8
Thanked 4 Times in 3 Posts
Rep Power: 206
James will become famous soon enoughJames will become famous soon enoughJames will become famous soon enough
Default Re: Overcharging alternator and buzzing voltage regulator

Quote:
Originally Posted by AZKen View Post
I don't do one wire, just normal 2/3 wire. Hope all is good now. There is not much time savings in one wire really.
I agree a one wire alternator is a bad choice. They can cause more problems than they're worth. Ideally the alternator should sense the voltage near the fuse block. This will minimize voltage fluctuation. Example of one wire alternator problems: Headlight going dim then back to normal when the turn signal flashes. Been there done that.
Reply With Quote
  #8  
Old March 24th, 2021, 10:12 PM
James James is offline
-= Extreme Supporter =-
 
Join Date: Jun 2013
Location: Greer, SC
Truck: 1964 GMC 1500 2wd
Age: 69
Posts: 449
Thanks: 8
Thanked 4 Times in 3 Posts
Rep Power: 206
James will become famous soon enoughJames will become famous soon enoughJames will become famous soon enough
Default Re: Overcharging alternator and buzzing voltage regulator

Quote:
Originally Posted by biscaynebirdie View Post
I’ve read that the one wire alternator is a major time saver. However, today I actually managed to get the original voltage regulator back in working order! 12.7 volts at idle, 13.5 volts around 1500 RPM, and goes about as high as 15 volts when I’m really giving it gas. Everything seems okay for now. If this doesn’t last, I’ll convert to the one wire alternator.
One thing that can make the voltage high is a bad connection(s). With the engine running. Take your volt meter and measure the voltage drop from the positive battery post (not the clamp) and the output stud on the alternator. You should see no more than 1/2 volt. Do the same thing on the battery negative post to the case of the alternator. You should see no more than 1/2 volt. In fact less voltage is better. I seen more alternator ground problems than anything else.

Let me know if you have a high reading (more than 1/2 volt) and on which circuit (positive or negative).
Reply With Quote
  #9  
Old March 27th, 2021, 01:34 AM
Quigley's Avatar
Quigley Quigley is offline
Senior Member
 
Join Date: Mar 2013
Location: New Hampton,Iowa
Truck: 1966 1000 Wideside 1962 1500 Wideside 401 Magnum
Posts: 187
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 134
Quigley will become famous soon enoughQuigley will become famous soon enough
Default Re: Overcharging alternator and buzzing voltage regulator

I had the same problem with my 66 and put on two Delco voltage regulators and both made a buzzing sound and did not work. Bought a cheap electronic regulator from Car Quest problem solved and has worked perfectly ever since.
Reply With Quote
  #10  
Old March 27th, 2021, 05:50 AM
biscaynebirdie biscaynebirdie is offline
Junior Member
 
Join Date: Jan 2021
Location: Santa Rosa, California
Truck: 1965 1000 Series with 250 engine and SM420 transmission
Posts: 26
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 30
biscaynebirdie is on a distinguished road
Default Re: Overcharging alternator and buzzing voltage regulator

Thank you all for your comments and advice! I’ve been spending a lot of time adjusting the contact gap and spring tension in that regulator, and I think that I have it at a point where it isn’t going to undercharge or overcharge my battery (even though I have no idea what in the **** I am doing). I went for a brief drive tonight and measured the voltage at idle once I got back. I had been running the heater blower, headlights, and turn signals during the drive but shut them off once I pulled into the driveway. At idle with no accessories on other than the running lights, my meter read 12.9 volts at the battery posts. Sound okay?
Quote:
Originally Posted by James View Post
I seen more alternator ground problems than anything else.
Funny you should mention it... I ended up running a ground wire directly from the ground post on the alternator to the ground screw on the regulator box. For some reason we hadn’t run one in the first place. Probably one reason it isn’t acting up as much.

I’ll follow your instructions and let you know what my results are. Probably going to be a day or two before I can get around to doing it.
Reply With Quote
Reply

Bookmarks

Tags
charging problems, overcharging, voltage regulator

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Voltage Regulator Replacement zoulas Interiors, Dash, Lights and Electrical 13 July 26th, 2022 08:26 AM
Voltage Regulator Question Archiver Previous Forum Posts 2 January 15th, 2013 12:55 AM
external voltage regulator Archiver Previous Forum Posts 0 November 16th, 2003 12:25 AM
Testing voltage regulator Archiver Previous Forum Posts 0 April 5th, 2002 12:55 AM
Re: Testing voltage regulator? Archiver Previous Forum Posts 0 April 1st, 2002 12:39 AM


All times are GMT +1. The time now is 08:05 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 771729009125|1727809506|0