6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Builds and Journals
#Sponsored

Builds and Journals This is where the magic happens. Photograph & document your GMC build progress for posterity.
NOTICE - Photobucket will delete your pics after a time. Use another host if possible.

Reply
 
Thread Tools
  #91  
Old April 10th, 2023, 07:24 PM
Prowbar Prowbar is offline
-= Dues Paid =-
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 452
Thanks: 11
Thanked 13 Times in 12 Posts
Rep Power: 204
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: '65 GMC 1500 project. From the Netherlands

Installed the 478 today. Took the engine off the stand with the engine hoist, then installed the bell housing, flywheel, pressure plate, clutch, starter, engine wiring harness. Checked the bell housing runout, .003". Pilot bearing runout is less than .002". Used the same method of removing the rocker assemblies and using a head bolt with a piece of strip as a mount for the chain.
Very satisfied with the install. Then installed the transmission.
Had to take the SM420 top cover off to clear the firewall.
Used new motor mounts (Thanks for the Anchor part numbers, Funky61)

After installation, we pulled the engine as much forward as we could to give the right side exhaust manifold as much clearance as possible. There is about 7/16" clearance between the manifold and firewall now.

Now, onto reinstalling the rest...
Attached Images
File Type: jpg 20230410_154104.jpg (4.26 MB, Multiple views, 8 clicks)
File Type: jpg 20230410_162321.jpg (3.89 MB, Multiple views, 8 clicks)
File Type: jpg 20230410_163610.jpg (3.88 MB, Multiple views, 6 clicks)
File Type: jpg 20230410_171444.jpg (4.29 MB, Multiple views, 7 clicks)
File Type: jpg 20230410_171450.jpg (4.50 MB, Multiple views, 7 clicks)
Reply With Quote
  #92  
Old April 22nd, 2023, 07:07 PM
Prowbar Prowbar is offline
-= Dues Paid =-
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 452
Thanks: 11
Thanked 13 Times in 12 Posts
Rep Power: 204
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: '65 GMC 1500 project. From the Netherlands

Been busy, but slowly building up the engine and hooking up everything.
Got most of the to-do list taken care of.
Hope to fire her up for the first time next week. I'll be sure to take a video.
We'll hook a manometer to the oil pressure sender, prime the engine beforehand, and then do a few rotations with the starter without the sparkplugs installed. Then add some gas to the carb and fire her up. Probably take her to 1000 RPM or so for 10 minutes and verify the lifters are rotating.

The carb fuel line is a temporary addition. It came with the carb and is easy for testing.
Attached Images
File Type: jpg 20230422_160739.jpg (4.08 MB, Multiple views, 9 clicks)
Reply With Quote
  #93  
Old April 30th, 2023, 06:42 PM
Prowbar Prowbar is offline
-= Dues Paid =-
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 452
Thanks: 11
Thanked 13 Times in 12 Posts
Rep Power: 204
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: '65 GMC 1500 project. From the Netherlands

What was supposed to be an easy start-up didn't turn out to be one. When we went to start the engine we quickly had coolant between the block and heads. Had some problems with poor starter performance as well. After a lot of attempts without any success, we gave up and drained the oil. Full of coolant...

Then made the decision to take off the heads. This went rather easily and soon was discovered that the coolant passages in the block do not line up with the head gasket. See pictures. This NOS head gasket (picture 5) only relies on crush rings to do the sealing. I never noticed this misalignment during assembly. This probably caused the leakage.
Also discovered that the cylinder crush rings seat inside the bore. Which is bad for detonation and gasket life.

Anyway, I have some Fel-pro 305/351 V6 head gaskets. They rely on gasket material instead of crush rings to provide the seal on the coolant passages. Fel-pro also turned these coolant passages into slots, which do line up, which is great. Even if they did not completely cover the bore, the gasket material would take care of the sealing. Now the bores still need to be opened up. I have tested one and it can be done, by moving the crush ring to a larger diameter. Now to make some specialized tooling to facilitate the process...

I was given the original GMC 478 head gaskets (that came off the engine, picture 3) as well. They line up properly. Which got me thinking... Maybe I've been given NOS 401 V6 head gaskets... which would explain the crush rings sticking into the bores...
And for the coolant passages, they probably moved them away from the bores to deal with the larger 478 bores... But this is speculation.

I'm glad we discovered it now instead of later... But it makes you feel like an idiot for not noticing.
Attached Images
File Type: jpg 20230428_152639.jpg (3.61 MB, Multiple views, 3 clicks)
File Type: jpg 20230428_152645.jpg (3.61 MB, Multiple views, 3 clicks)
File Type: jpg 20230428_154218.jpg (5.22 MB, Multiple views, 5 clicks)
File Type: jpg 20230428_163259.jpg (3.98 MB, Multiple views, 3 clicks)
File Type: jpg 20230428_152842.jpg (4.38 MB, Multiple views, 3 clicks)

Last edited by Prowbar; April 30th, 2023 at 09:59 PM.
Reply With Quote
  #94  
Old April 30th, 2023, 06:46 PM
Prowbar Prowbar is offline
-= Dues Paid =-
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 452
Thanks: 11
Thanked 13 Times in 12 Posts
Rep Power: 204
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: '65 GMC 1500 project. From the Netherlands

Picture of the 401 gasket (bottom) compared to the original 478 gasket (top). Notice the bore difference and the offset in coolant passages. What do you think?
Attached Images
File Type: jpg 20230430_184406.jpg (6.44 MB, Multiple views, 4 clicks)

Last edited by Prowbar; April 30th, 2023 at 09:59 PM.
Reply With Quote
  #95  
Old May 5th, 2023, 07:35 PM
Prowbar Prowbar is offline
-= Dues Paid =-
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 452
Thanks: 11
Thanked 13 Times in 12 Posts
Rep Power: 204
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: '65 GMC 1500 project. From the Netherlands

As talked about I made some tools to help form the gaskets from the 305/351 size to the 478. First off a plate with the locating dowels is made. In the center of each bore a hole is milled to hold a steel cup, which fits a bearing. This is the center is my bead roller setup.

The process starts by grinding down the old crush ring until they can be separated. This also separates the gasket. One bore is formed at a time, to keep the pieces properly located.

Then with a Dremel, the blue gasket layer is enlarged to 5.125" + some extra. A piece of plastic is stuck between the steel backing and blue gasket material to protect the steel backing from being cut.

Then with the roller and forming dies, the sheet metal backing is brought upwards and a new ring is formed. The length is then ground down to the right height and deburred. Then it is rolled over, forming a new crush ring. The sheet metal works easily and takes the shape well. The crush rings look good and smooth.

See the last picture for the finished modified gasket.

One head has already been installed with a new gasket. I also used some head gasket sealer as an added measure. So far it looks good. Tomorrow planning to reassemble the engine, then hopefully a first start without any troubles. I will be running straight water for the first start (without any calcium).

Of course, this is an experiment, maybe they blow out quickly, maybe not. We'll see. Some redneck engineering at its finest

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?

Attached Images
File Type: jpg 20230505_121639.jpg (3.57 MB, Multiple views, 2 clicks)
File Type: jpg 20230505_112240.jpg (3.75 MB, Multiple views, 3 clicks)
File Type: jpg 20230505_131446.jpg (4.50 MB, Multiple views, 3 clicks)
Reply With Quote
  #96  
Old May 6th, 2023, 07:02 PM
Prowbar Prowbar is offline
-= Dues Paid =-
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 452
Thanks: 11
Thanked 13 Times in 12 Posts
Rep Power: 204
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: '65 GMC 1500 project. From the Netherlands

Got this far today.
Attached Images
File Type: jpg 20230506_145316.jpg (4.92 MB, Multiple views, 8 clicks)
Reply With Quote
  #97  
Old May 13th, 2023, 05:13 PM
Prowbar Prowbar is offline
-= Dues Paid =-
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 452
Thanks: 11
Thanked 13 Times in 12 Posts
Rep Power: 204
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: '65 GMC 1500 project. From the Netherlands



To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?



First start of the 478 V6!
Reply With Quote
  #98  
Old May 14th, 2023, 01:38 PM
Prowbar Prowbar is offline
-= Dues Paid =-
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 452
Thanks: 11
Thanked 13 Times in 12 Posts
Rep Power: 204
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: '65 GMC 1500 project. From the Netherlands

Here is a video of the second run:

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?



Runs much better, throttle at idle wasn't opened far enough and we retarded the time some. Two of the valve lifters are spinning slowly, and two aren't spinning at all, these will be replaced with new Melling lifters from Rockauto.
For the experiment, I switched two lifters around, a fast and slow turning lifter, and the lifter is at fault, with no proper crown. These are the OEM lifters.

Lifters are easy to change, back off the valve lash adjustment, remove the pushrod and use a stick magnet to retrieve the lifter.

The 305 starter doesn't have the oomph and drains the battery rather quickly, have to figure out what causes it.

The haze from the manifolds is the paint baking.

Last edited by Prowbar; May 14th, 2023 at 05:29 PM.
Reply With Quote
  #99  
Old May 20th, 2023, 10:41 PM
Prowbar Prowbar is offline
-= Dues Paid =-
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 452
Thanks: 11
Thanked 13 Times in 12 Posts
Rep Power: 204
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: '65 GMC 1500 project. From the Netherlands

Bought me some new Melling lifters from Rockauto to replace the slow-turning or stationary lifters. After replacing them with the Melling lifters nothing happens at all.

Pretty ticked off. Makes me wonder if the cam is still decent. I measured the lobe lift before assembly and all intake/exhaust lobes had about equal height, but I couldn't detect any noticeable taper then. Might have to pull the cam, and have it reground, along with the lifters... Not the news I was waiting for, to say the least

To view some links or images in this forum your post count must be 1 or greater. You currently have 0 posts. Maybe you should introduce yourself with a new topic?



I am using oil with proper ZDDP content.
Reply With Quote
  #100  
Old May 26th, 2023, 09:21 PM
Prowbar Prowbar is offline
-= Dues Paid =-
 
Join Date: Dec 2020
Location: Friesland, the Netherlands
Truck: 1965 GMC 1500, 478 V6, SM420
Posts: 452
Thanks: 11
Thanked 13 Times in 12 Posts
Rep Power: 204
Prowbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the roughProwbar is a jewel in the rough
Default Re: '65 GMC 1500 project. From the Netherlands

Going to pull the camshaft out and have it reground according to Bigblock V6 (Pete) specs. Also, new lifters.

Need to wait a bit before I can get the cam ground, but in the meanwhile, I can finish most of the tasks that still need doing:

Remove the camshaft
Exhaust downpipes welding. Bought an air-fuel meter to install.
Propane mixer adapter
New battery cables
Leaking rear axle seal
All sorts of odd jobs that need to be done

Keeps one busy.

Traced the slow starting to the starter itself. Have to look it over. Seems like the new brushes aren't seating properly. When the switched them for the old brushes, it cranked over just fine.
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Wanted: Speaker Bracket for '65 1500 lhtex120 1960-1966 GMC Marketplace 8 September 19th, 2014 10:46 PM
I need and engine. 305 in a 65 1500 fleetside Archiver Previous Forum Posts 0 February 17th, 2007 01:25 AM
1985 brake swap into 65 1500 Archiver Previous Forum Posts 0 February 27th, 2006 01:57 AM
Re: [6066 GMC] brake shoes 65 1500 Archiver Previous Forum Posts 0 July 12th, 2004 02:12 AM
brake shoes 65 1500 Archiver Previous Forum Posts 0 July 11th, 2004 02:12 AM


All times are GMT +1. The time now is 02:20 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 861733498009|1732454445|0