Pay Dues or become a Site Supporter
|
Pay Dues or become a Site Supporter
|
|
#1
May 31st, 2021, 09:29 PM
|
|||
|
|||
My oil filter solution.
I thought I try a different approach in resolving the canister oil filter. I design and had a machine shop made an adapter bolt and plate. My adapter can use any filter the small or big block Chevy can use. Next weekend I will be installing my new adapter. This setup also keep the original oil by-pass valve. And If I wanted to convert it back it would be no problem, but why would I.
|
|
#2
May 31st, 2021, 09:57 PM
|
||||
|
||||
|
Re: My oil filter solution.
Oh My James that looks AMAZING! Any more planned in the future; I'd be interested in one.
Tuned in for the follow-up  
__________________
1961 GMC Suburban 305A Overdrive 1962 GMC Utility 305D
|
|
#3
June 1st, 2021, 06:28 PM
|
||||
|
||||
|
Re: My oil filter solution.
A Bump for Excellence!
__________________
1961 GMC Suburban 305A Overdrive 1962 GMC Utility 305D
|
|
#4
June 4th, 2021, 02:28 PM
|
||||
|
||||
|
Re: My oil filter solution.
Thats a cool idea, how big are the holes? Maybe oblong them out alittle more for better flow
|
|
#5
June 5th, 2021, 06:55 PM
|
|||
|
|||
|
Re: My oil filter solution.
Quote:
|
|
#6
June 5th, 2021, 07:16 PM
|
|||
|
|||
|
Re: My oil filter solution.
I installed my new oil filter adapter with mixed results. Removed the canister/filter and gasket. Installation of the new adapter went well, everything fit. Could not install the tall oil filter due to the stock exhaust system is in the way. Checked the oil level it was full, so I started the engine. Good thing I place the drain pan under the filter. The adapter plate, on the aft side, was streaming oil.
 Shut down the engine took the adapter off and double check the mating surface, everything clean (no gasket material). Reassembled and tried again. Same problems. Took it apart again and placed the old gasket back in, thinking the seal need more compression. Installed the adapter/filter. Ran the engine, no leaks. Topped off the oil. Went on a 74 miles trip around the country side, no leaks. Next time I change oil I'll look deeper into why it leak. 
|
|
#7
June 5th, 2021, 08:17 PM
|
|||
|
|||
|
Re: My oil filter solution.
GMC oil filter adapter.png Another alternative is a spin on adapter for Detroit Diesels as they share the same filter cannister as the gas GMC V6
|
|
#8
June 5th, 2021, 08:49 PM
|
|||
|
|||
|
Re: My oil filter solution.
Quote:
|
|
#9
June 6th, 2021, 08:27 PM
|
||||
|
||||
|
Re: My oil filter solution.
James, that canister photo is what I have under my 62, and access was tough because the exhaust had been pushed up on it. It was a challenge to get it up there so I can see why you made the conversion plate.
__________________
1961 GMC Suburban 305A Overdrive 1962 GMC Utility 305D
|
|
#10
September 19th, 2021, 11:32 PM
|
||||
|
||||
|
Re: My oil filter solution.
FYI; that ACDELCO K4 adapter will not work
__________________
1961 GMC Suburban 305A Overdrive 1962 GMC Utility 305D
|
 |
| Bookmarks |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Oil leaking from top of oil filter canister | Snags | GMC V6 and V12 Engines | 3 | January 8th, 2015 07:50 PM |
| 1965 V6 SPIN ON OIL FILTER & PCV FILTER | Archiver | Previous Forum Posts | 0 | February 23rd, 2006 01:39 PM |
| Re: [6066 GMC] 1965 V6 SPIN ON OIL FILTER & PCV FILTER | Archiver | Previous Forum Posts | 0 | February 23rd, 2006 12:29 AM |
| RE: [6066 GMC] 1965 V6 SPIN ON OIL FILTER & PCV FILTER | Archiver | Previous Forum Posts | 0 | February 23rd, 2006 12:21 AM |
| solution to over heating problems | Archiver | Previous Forum Posts | 0 | October 29th, 2005 05:13 AM |
