6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Transmissions and Rear Ends


Transmissions and Rear Ends Three on the tree or four in the floor? Shift it all here.

Reply
 
Thread Tools
  #1  
Old August 1st, 2016, 04:37 PM
Chuck78 Chuck78 is offline
Member
 
Join Date: Jul 2014
Location: Columbus OH
Truck: 1962 GMC 1000 panel truck
Age: 45
Posts: 90
Rep Power: 82
Chuck78 is on a distinguished road
Default 62 GMC 1000 Panel - which clutch throwout bearing?

I failed to measure my TO bearing when I had to pull the engine last (replaced front and rear cylinder head freeze plugs, firewall side were disentegrated). Now on looking them up, I see there is a long style and three short versions all from the same manufacturer. I seem to think from recollection that it may be the long style.

Can anyone verify this or simply tell me that all of these listed for my model on Rock Auto could possibly have been used depending on transmission or clutch type?

It had an SM318 3ott, then T5, then SM318 when I got it, blew that up and put in a Saginaw 4 speed with existing TO bearing. Now looking to swap an Aisin AX15 5 speed or possibly A833/NP440 MY6 with gm bell pattern.

305D swapping to 351C next time I pull engine to swap in disc brake crossmember.

Attached Images
File Type: png Screenshot_2016-08-01-11-17-18.png (422.0 KB, Multiple views, 31 clicks)
__________________
Chuck in Ohio
*'62 GMC 1000 Panel Truck - 305D/Saginaw 4sp soon: 351C V6 + AX15 5sp OD trans, & 73-87/91 disc brake front end, rear Cadillac calipers/ AWD Astro rotors, Dana 44 redrilled to 5 lug
*'88 Suzuki Samurai 4x4 project, VW 1.9L mTDI turbodiesel, Toyota V6 LandCruiser drivetrain, full floater axles, future LWB bed stretch
*'77-'79 Suzuki GS motorcycles, '76 Rickman CR900 roadracer.
*Dirtbikes: 2 Kawasaki KDX220R's, '77 Suzuki PE250, '83 PE175
Reply With Quote
  #2  
Old August 1st, 2016, 06:56 PM
David R Leifheit's Avatar
David R Leifheit David R Leifheit is offline
Senior Member
 
Join Date: Jan 2013
Location: Dallas, Oregon
Truck: 1960-1966 1000-4000 series
Age: 62
Posts: 281
Rep Power: 166
David R Leifheit is a jewel in the roughDavid R Leifheit is a jewel in the roughDavid R Leifheit is a jewel in the rough
Default Re: 62 GMC 1000 Panel - which clutch throwout bearing?

Long throwout vs. short is dependent upon the pivot point for the clutch. There are two sizes, a long one and a short one.

I seem to recall if it is the short pivot, then the long throw out.

you show two diameters of clutch slave, those I can't advise on.
__________________
--
- David R Leifheit
in Dallas, Oregon
mailto:
To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

(2) 1961 1500
1962 1000
1963 2500
1963 4000
1964 2500
Reply With Quote
  #3  
Old August 1st, 2016, 07:38 PM
Chuck78 Chuck78 is offline
Member
 
Join Date: Jul 2014
Location: Columbus OH
Truck: 1962 GMC 1000 panel truck
Age: 45
Posts: 90
Rep Power: 82
Chuck78 is on a distinguished road
Default Re: 62 GMC 1000 Panel - which clutch throwout bearing?

Ahhhh... you just reminded me that the pivot ball is worn out as well...
Any idea on a part number or source for those? Standard GM part that is fairly universal?
__________________
Chuck in Ohio
*'62 GMC 1000 Panel Truck - 305D/Saginaw 4sp soon: 351C V6 + AX15 5sp OD trans, & 73-87/91 disc brake front end, rear Cadillac calipers/ AWD Astro rotors, Dana 44 redrilled to 5 lug
*'88 Suzuki Samurai 4x4 project, VW 1.9L mTDI turbodiesel, Toyota V6 LandCruiser drivetrain, full floater axles, future LWB bed stretch
*'77-'79 Suzuki GS motorcycles, '76 Rickman CR900 roadracer.
*Dirtbikes: 2 Kawasaki KDX220R's, '77 Suzuki PE250, '83 PE175
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Re: [6066 GMC] 66 gmc clutch,pressure plate and throwout bearing Archiver Previous Forum Posts 0 March 24th, 2006 09:36 AM
Re: [6066 GMC] 66 gmc clutch,pressure plate and throwout bearing Archiver Previous Forum Posts 0 March 24th, 2006 05:20 AM
Re: [6066 GMC] 66 gmc clutch,pressure plate and throwout bearing Archiver Previous Forum Posts 0 March 24th, 2006 02:35 AM
Re: [6066 GMC] 66 GMC clutch, pressure plate & throwout bearing Archiver Previous Forum Posts 0 March 24th, 2006 12:57 AM
66 gmc clutch,pressure plate and throwout bearing Archiver Previous Forum Posts 0 March 23rd, 2006 03:31 AM


All times are GMT +1. The time now is 12:31 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 681711554703|1710415878|0