6066 (1960-1966) GMC Truck Club Bitcoin now accepted here! 
Pay Dues
Pay Dues or become a Site Supporter
 



Go Back   6066 (1960-1966) GMC Truck Club > 6066 GMC Truck Club Forum > Exterior, Bodywork, Paint and Glass
#Sponsored

Exterior, Bodywork, Paint and Glass Beauty is only 4 coats deep...

Reply
 
Thread Tools
  #1  
Old October 10th, 2014, 06:37 PM
aphaynes's Avatar
aphaynes aphaynes is offline
-= Site Supporter =-
 
Join Date: Mar 2014
Location: Athens, AL
Truck: 1965 GMC 1000
Posts: 397
Thanks: 1
Thanked 1 Time in 1 Post
Rep Power: 169
aphaynes is on a distinguished road
Default Rear Bumper mounting

I tried putting this in my build journal but have not gotten any answers. So, please excuse the double post...

Well, I am about ready to remove this funky bumper.



However, I have some questions about mounting the standard bumper. First, I assumed, for no apparent reason, that due to the shape of the brackets that the frame would fit between the two bracket pieces on each side. However, in this image from the 1960-1966 Chevy/GMC Truck Assembly manual, it appears that both bracket pieces sit on the outside of the frame rail. Is this correct?



Also, since my funky bumper was welded to the frame, I have to figure out how to get it off.





It is not apparent in these two pics, but they welded a cross piece between the frame rails as well which have more metal brackets welded between it and the bumper. I am hoping it is far enough back to be out of the way with the funky bumper off. Although in the second pick I am thinking the weld and splatter are interfering with what I assume to be one of the bolt holes.

Once I do get the bumper off, I am really not sure what holes to use to mount the brackets to. Does anyone have pics that show their bumper brackets mounted to the frame? ...Thanks.
Reply With Quote
  #2  
Old October 10th, 2014, 08:20 PM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,780
Thanks: 19
Thanked 4 Times in 3 Posts
Rep Power: 570
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: Rear Bumper mounting

I would probably run a grinder on the bumper mounts outside the bumper and just grind them off to pokey points so the bumper falls off on the ground while I'm in the truck bed. Then I'd crawl under it and grind the welds off for safety. Those little brackets hurt less than a whole bumper would.

I can't help with the mounts though. I think Mr Foley posted some pics of a factory mount a few months back. I'll see if I can find them...Wait right here.....
__________________
Step by steps:

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Some people are like slinkys. Not worth much but funny as heck when pushed down stairs.
__________________
If the women don't find you handsome, they should at least find you handy.

Last edited by FetchMeAPepsi; October 10th, 2014 at 08:25 PM.
Reply With Quote
  #3  
Old October 10th, 2014, 08:25 PM
FetchMeAPepsi's Avatar
FetchMeAPepsi FetchMeAPepsi is offline
-= Dues Paid =-
 
Join Date: Jan 2013
Location: Edmond, Ks
Truck: 1962 4x4 GMC CECILIA
Posts: 1,780
Thanks: 19
Thanked 4 Times in 3 Posts
Rep Power: 570
FetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of lightFetchMeAPepsi is a glorious beacon of light
Default Re: Rear Bumper mounting

It was DAC, not Foley. Here's a link:

http://6066gmcclub.com/forum/showthr...2707#post52707

Hope that points you in the right direction. Bumpers are HEAVY so be careful and have your helper take lots of pics
__________________
Step by steps:

To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.


To view links or images in signatures your post count must be 0 or greater. You currently have 0 posts.

Some people are like slinkys. Not worth much but funny as heck when pushed down stairs.
__________________
If the women don't find you handsome, they should at least find you handy.
Reply With Quote
  #4  
Old October 11th, 2014, 01:49 AM
GMCDAC's Avatar
GMCDAC GMCDAC is offline
Senior Member
 
Join Date: Jan 2013
Location: Green Valley, east of Rapid City,SD
Truck: I have 4 GMCs, none with a V-6 - YET! Have had 2 in the family.
Age: 67
Posts: 553
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 213
GMCDAC is on a distinguished road
Default Re: Rear Bumper mounting

Quote:
Originally Posted by FetchMeAPepsi View Post
It was DAC, not Foley. Here's a link:

http://6066gmcclub.com/forum/showthr...2707#post52707

Hope that points you in the right direction. Bumpers are HEAVY so be careful and have your helper take lots of pics
Hi guys, those brackets I posted are factory made, but not a GMC factory. They were probably made by the bumper manufacturer. They are for an aftermarket bumper probably similar to the bumper Aphaynes is removing.

Fetch is right on, the welds don't look substantial enough where cutting them with a grinder shouldn't be too difficult.

DAC
__________________
Doug Crawford
Rapid City, SD

1970 GMC K5 Jimmy Mom drove 30 years
1972 GMC C2500 owned since 1979
1955 GMC 100 driver-project
2006 GMC Yukon Denali---wife's truck

Hope to have a '60 GMC Suburban again someday
Reply With Quote
  #5  
Old October 11th, 2014, 04:30 AM
aphaynes's Avatar
aphaynes aphaynes is offline
-= Site Supporter =-
 
Join Date: Mar 2014
Location: Athens, AL
Truck: 1965 GMC 1000
Posts: 397
Thanks: 1
Thanked 1 Time in 1 Post
Rep Power: 169
aphaynes is on a distinguished road
Default Re: Rear Bumper mounting

Quote:
Originally Posted by GMCDAC View Post
Hi guys, those brackets I posted are factory made, but not a GMC factory. They were probably made by the bumper manufacturer. They are for an aftermarket bumper probably similar to the bumper Aphaynes is removing.

Fetch is right on, the welds don't look substantial enough where cutting them with a grinder shouldn't be too difficult.

DAC
Thanks guys. Yeah DAC, I wish whoever put that bumper on would have used brackets. I guess way back whenever, they had a reason for welding it in like that.

I just spotted a metal & fab shop about two miles from my house I have never noticed. Evidently they have been there for about a year now. I stopped in with Rusty and they said they could cut it off and clean it up for about $40. Since my tools are few I am thinking it might be worth to let them do it. However, with the brackets for my standard bumper, I am still not sure which holes they bolt to. Once the ugly bumper is out of the way, I will be able to figure it out I think.
Reply With Quote
  #6  
Old March 12th, 2023, 08:30 PM
CALGMC CALGMC is offline
Junior Member
 
Join Date: Nov 2020
Location: San Jose
Truck: 1964 GMC C1000
Posts: 29
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 35
CALGMC is on a distinguished road
Default Re: Rear Bumper mounting

I am in the process of mounting my new bumper. I do not like how far it sits out. Seems that rear leaf spring mount is in the way of pushing sport bumper closer. What are other GMC owners doing to get bumper closer? Are there special bumper brackets for leaf spring trucks, like there are for the 67-72 trucks?
Attached Images
File Type: jpg PXL_20230311_183248350.jpg (1.66 MB, Multiple views, 4 clicks)
File Type: jpg PXL_20230311_183257839.jpg (1.80 MB, Multiple views, 3 clicks)
File Type: jpg PXL_20230311_183319133.jpg (2.03 MB, Multiple views, 3 clicks)
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Looking for a rear bumper IndianJoe 1960-1966 GMC Marketplace 2 March 18th, 2013 03:31 PM
Rear Bumper Bracket Archiver Previous Forum Posts 0 February 2nd, 2011 04:22 AM
Strange rear Bumper Archiver Previous Forum Posts 1 January 30th, 2011 01:00 AM
rear bumper brackets Archiver Previous Forum Posts 0 October 3rd, 2005 06:07 AM
Rear Bumper Archiver Previous Forum Posts 0 March 3rd, 2005 08:34 AM


All times are GMT +1. The time now is 02:58 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2013, Jelsoft Enterprises Ltd 751730915004|1729821521|0